Removing/Inserting The Battery - Milwaukee 2552-20 Manual Del Operador

Llaves de impacto de 1/4" & destornillador hexagonal de impacto de 6 mm (1/4") de m12 fuel
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Use only sockets and other accessories specifi-
cally designed for use on impact wrenches and
drivers. Other sockets and accessories might
shatter or break causing injury.
Attaching and Removing Accessories
Square Drive Shank
(Cat. No. 2552-20)
These impact wrenchs are intended only for use with
sockets designed for impact wrenches that have a
1/4" square drive. Other sockets could shatter or
break, causing injury.
1. To attach a socket or other accessory, align the
accessory with the drive shank and push it firmly
over the retaining ring.
2. To remove the accessory, pull the accessory off
the drive shank.
Hex Drive Chuck
(Cat. No. 2553-20)
This driver is intended for use with drill
and driver bits with a 1/4" hex shank and
ball detent recess.
1. To attach an accessory, press the
shank into the hex drive chuck.
2. To remove the accessory, pull out
the ring and remove the accessory.
Release the ring.
OPERATION
Always remove battery pack before
WARNING
changing or removing accesso-
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, always wear proper
eye protection marked to comply with ANSI Z87.1.
When working in dusty situations, wear appro-
priate respiratory protection or use an OSHA
compliant dust extraction solution.
Fuel Gauge
To determine the amount of charge left in the battery,
turn the tool ON. The Fuel Gauge will light up for 2-3
seconds. When less than 10% of charge is left, 1 light
on the fuel gauge will flash 4 times.
To signal the end of charge, 1 light on the fuel gauge
will flash 8 times and the tool will not run. Charge
the battery pack.
If the battery becomes too hot, the fuel gauge lights
will flash in an alternating pattern and the tool will not
run. Allow the battery to cool down.
Using the Drive Control
(Cat. No. 2552-20)
The drive control button is used
to adjust the rotation speed
(RPM) for the application.
To select the drive control
mode:
1. Pull and release the trigger
to turn on the tool. The cur-
rent indicator is lit.
2. Press the drive control but-
ton
to cycle through the
4 modes. When the desired
mode indicator is lit, begin
work.
* In auto shut off mode
the tool will drive for-
ward at a reduced RPM
u n t i l t h e t o r q u e i s
achieved. In reverse the
tool will operate at full
RPM to remove fasten-
ers at full torque.
(Cat. No. 2553-20)
The drive control button is
used to adjust the rota-
tion speed (RPM) for
the application.
To select the drive con-
trol mode:
1. Pull and release the
trigger to turn on the
tool. The current in-
dicator is lit.
2. Press the drive control
b u t t o n
t o c y c l e
through the 4 modes.
When the desired mode
indicator is lit, begin
work.
* In self tapping screw
mode, the tool will drive
at full RPM until the
screw taps. Then, for better control, the RPM will
slow as the screw seats to the workpiece.
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
Push for
Forward
PUSH TO CENTER TO LOCK
1. For forward (clockwise) rotation, push the control
switch in the direction shown. Check the direction
of rotation before use.
2. For reverse (counterclockwise) rotation, push the
control switch in the direction shown. Check the
direction of rotation before use.
4
Speed Indicator
Drive
Control
Auto Shut
Button
Off Mode
Mode
RPM
,
1
0-1300
0-1300
2
0-1900
0-2000
3
0-3200
0-4300
0-3200*
Drive Control Button
Speed
Indicator
Tapping Screw Mode
Mode
RPM
1
0-1300
2
0-2400
0-2700
3
0-3300
0-4000
0-3300* 0-4000
Push for
Reverse
IPM
-
IPM
0-850

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

2553-202553-22

Tabla de contenido