Removing/Inserting The Battery - Milwaukee 2865-20 Manual Del Operador

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Attaching and Removing the Tool Hanger
1. To attach, place the hanger ring through the tool
hanger.
2. Position the tool hanger on the tool over the two
screw holes.
3. Insert the two screws. Hand tighten the screws.
4. To remove, reverse the procedure.
Use only sockets and other acces-
WARNING
sories specifically designed for
use on impact wrenches and drivers. Other
sockets and accessories might shatter or break
causing injury.
Attaching and Removing Accessories
This impact driver is intended for use
with drill and driver bits.
1. To attach an accessory, press
the shank into the hex drive
QUIK-LOK™chuck.
2. To remove the accessory, pull
out the QUIK-LOK™chuck ring
and remove the accessory.
Release the ring.
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, please reference the Quick Start
guide included with this product or go to
milwaukeetool.com/One-Key. To download the
ONE-KEY™ app, visit the App Store or Google Play
from your smart device.
When the product experiences ESD, the speed LED
shuts down and the product cannot adjust speed.
It needs the battery and coin cell removed and
reinserted to recover.
We considered the results to be within our minimum
acceptable performance level according to EN
55014-2/EN 301489-1/EN 301489-17.
ONE-KEY™ Indicator
Wireless mode is active and ready
Solid Blue to be configured via the ONE-KEY™
app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Tool is in security lockout and can
Blinking Red be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
Always remove battery pack before
WARNING
changing or removing accesso-
ries. Only use accessories specifically recom-
mended for this tool. Others may be hazardous.
To reduce the risk of injury, always wear proper
eye protection marked to comply with ANSI Z87.1.
Using the Drive Control
The drive control button is used to adjust the torque,
rotation speed (RPM), and impact speed (IPM) for
the application.
To select the drive control mode:
1. Pull and release the trigger
to turn on the tool. The cur-
rent mode indicator is lit.
2. Press the drive control but-
ton to cycle through the
modes. Select wireless
to change the default set-
tings via the ONE-KEY™
App on your smart device. When the desired mode
indicator is lit, begin work.
NOTE: Select the torque range in accordance with
the equipment manufacturers fastening instruc-
tions. For precision applications, confirm the final
tightening torque with a calibrated device.
Mode RPM IPM
1 0-900 0-800
2 0-1200 0-1300
Using the Control Switch
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow the
motor to come to a complete stop before using the
control switch.
Push for
Forward
PUSH TO CENTER TO LOCK
1. For forward (clockwise) rotation, push the control
switch in the direction shown. Check the direction
of rotation before use.
2. For reverse (counterclockwise) rotation, push the
control switch in the direction shown. Check the
direction of rotation before use.
3. To lock the trigger, push the control switch to the
center position. The trigger will not work when the
control switch is in the locked position.
Always remove the battery pack before performing
maintenance or changing accessories. Always
lock the trigger or remove the battery pack before
storing the tool and any time the tool is not in use.
4
Drive Control Button
Mode
ONE-KEY™
Indicator
Mode RPM IPM
3 0-1800 0-2600
4 0-2300 0-2800
Push for
Reverse