GE Profile GSMF2LEB Manual De Uso Y Cuidado página 47

Ocultar thumbs Ver también para Profile GSMF2LEB:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

About the temperature controls.
Not all features are on all models. Your controls will look like one of the following:
Actual Temp Control
To run your refrigerator:
Connect the power supply.
Select the temperature control (to adjust the temperature of
your refirgerator in accordance with the amount of your food
and climate of your city. The temperature controls are preset
in the factory at 3˚C (37˚F) for the refrigerator compartment
and -18˚C (0˚F) for the freezer compartment. Allow 24 hours
for the temperature to stabilize to the preset recommended
settings.
Refrigerator temperatures can be adjusted between 1˚C and
7˚C (34˚F to 44˚F), and the freezer temperatures can be
adjusted between -21˚C and -14˚C (-6˚F to 6˚F).
Note: The products marketed in the Andean Countries
have been evaluated under the following ranges of
temperature:
ST (Subtropical) between 18˚C and 38˚C.
T (Tropical) between 18˚C and 43˚C.
To change the Refrigerator room temperature:
LCD Models:
Access By: Home > Refrigerator
Activated By: Using the arrows to select the desired
temperature.
To change the Refrigerator room temperature:
LCD Models:
Access By: Home > Refrigerator
Activated By: Using the arrows to select the desired
temperature.
You must press ENTER to set the new temperature.
Once the desired temperature has been set, the display will
return to the HOME screen and show the set temperatures
underneath the actual temperature display for several
seconds. Several adjustments may be required. each time
you adjust the controls, allow 24 hours for the refrigerator to
reach the temperature you have set.
Non-LCD Models:
To change the temperature, press and release the WARMER
or COLDER pad. The SET light will come on and the display
will show the set temperature. To change the temperature,
tap either the WARMER or COLDER pad until the desired
temperature is displayed
.
Actual Temp Control
Non-LCD models
LCD models
NOTE: The refrigerator is shipped with protective film
covering the temperature controls. If this film was not
removed during installation, remove it now.
To adjust the Actual Temp Control temperature, first press
the Freezer (Temperature) or Refrigerator (Temperature)
button. Then press WARMER (
increase or decrease temperature to the desired setting.
Once the desired temperature has been set, the temperature
display will return to the actual refrigerator and freezer
temperatures after 5 seconds. Several adjustments may be
required. Each time you adjust the control, allow 24 hours for
the refrigerator to reach the temperature you have set. The
temperature controls can display both the SET temperature as
well as the actual temperature in the refrigerator and freezer.
The actual temperature may vary slightly from the temperature
based on usage and operating enviroment.
Turning the cooling system off:
LCD models: Turning the cooling system OFF stops cooling
in both the freezer and refrigerator compartments, but does not
shut off electrical power to the refrigerator.
Non-LCD models: Setting either or both controls to OFF stops
cooling in both the freezer and refrigeartor compartments, but
does not shut off electrical power to the refrigerator.
LCD Models:
Access By: Home > Options > Information and Settings >
Cooling System Off
To return the cooling system back on, press the touch screen
and press the ON button.
Activate by: Pressing ENTER.
Non-LCD Models:
Tap the WARMER pad for either the refrigerator or the freezer
until the display shows OFF. To turn the unit back on, press the
COLDER pad for either the refrigerator or freezer. The SET light
will illuminate on the side you selected. Then press the COLDER
pad again (on the side where the SET light is illuminated) and it
will go to the preset points of -18˚C (0˚F) for the freezer and 3˚C
(37˚F) for the refrigerator.
Setting the Actual Temp Control to 0 stops cooling in both the
freezer and refrigerator compartments, but does not shut off
electrical power to the refrigerator.
When the unit is turned back on, it will take up to 24 hours to
stabilize.
) or COLDER (
) to
45

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Profile gsmt2lebProfile psmf2lebProfile psmt2leb

Tabla de contenido