Notifications; Sleepcube Travel Information; Sleepcube Dc Operation; Battery Power - DeVilbiss Healthcare SleepCube Standard CPAP DV51 Serie Guía De Instrucciones

traVEl/Dc opEration/SupplEmEntal oxygEn
attached to your device, which provides additional messages. Refer to the documentation that was provided with the SmartLink Module.
clean Filter – The filter should be checked every 10 days for signs of dirt or wear so that it can be cleaned as needed.
This message helps to remind you to check it regularly.

Notifications

Notifications identify conditions in your SleepCube that may require action by you or your home care provider in order to maintain a high level of
therapy. If you see a message on the display that is not listed below, you may have the optional DeVilbiss SmartLink Module attached to your device,
which provides additional messages. Refer to the documentation that was provided with the SmartLink Module.
NOTE
-The values displayed are examples only.
Delay Running xx Minutes Left – While a comfort delay session is active, this message is flashed on the display every 5
seconds to let you know how much time is left in the delay.
Mask Off – This message appears whenever a high airflow condition occurs. High airflow is normally due to a poor mask
fit or a removed mask. Check for leak around the mask seal and make adjustments as necessary according to the mask
manufacturer's instructions. This message will be displayed until the high airflow problem is corrected. If the high airflow
condition persists for about 20 seconds, the device will automatically turn off (if AutoOFF is enabled).
Device Fault – If a device fault message is displayed, refer to Troubleshooting for instructions.

sleePCUbe TRaVel infoRmaTion

International Power changes
Your DeVilbiss SleepCube is equipped with a universal power supply. This means that it is automatically capable of accepting line voltages of 100 to
240V~ 50/60Hz. You do not need to make any adjustments to the device if you are traveling to another country where the line voltage is different
than your domestic line voltage. Simply contact your home care provider for the correct style power cord for the region in which you will be
traveling (refer to Accessories/Replacement Items for the correct part number).
Altitude
Your SleepCube automatically compensates for changes in altitude between sea level and 9000 ft (2750 m). You do not need to make adjustments
to the device for changes in altitude.

sleePCUbe DC oPeRaTion

Battery Power

Your SleepCube can be operated from a 12V DC power source in a motor home, boat or other recreational vehicle. The power source can be
used with a 12V DC accessory cable or a 12 V DC stand-alone battery. Both parts are available from your home care provider (refer to
Accessories/Replacement Items for the correct part numbers). Both accessory cables are required for stand-alone battery operation. The stand-
alone battery connection uses clamps that attach to the terminal connections of the battery.
NOTE
– The heater for the SleepCube's humidification system will not operate directly from a 12V DC power source. If you need humidification, passover humidification is still
available. Alternately, instead of connecting12V DC power directly to the SleepCube, you can pass the DC power through an inverter that will deliver AC power to the
system. This will allow the heater to function. The power rating of the inverter must be at least 200 watts @ 110V~ / 400 watts @ 220V~.
NOTE
– The SleepCube will automatically switch power sources between AC and 12V DC if both sources are available. If your unit is connected to both AC and 12V DC power
sources, it will operate on AC power as long as AC power is present, and automatically switch to 12V DC power if AC power is lost. When AC power is restored, it will
return to the AC source. You do not need to reset or adjust any settings when the power source switches, but remember that your heater will not operate on 12V DC.

sUPPlemenTal oXyGen

Supplemental oxygen is sometimes prescribed in addition to CPAP for treatment of Obstructive Sleep Apnea. If your physician prescribed oxygen
for your sleep therapy, you can add the oxygen in one of two ways:
1. Obtain the optional oxygen adapter (part #7353D-601) from your home care provider and connect it to the outlet port on the SleepCube.
Connect one end of the air supply tubing to the open end of the adapter and the other end of the air supply tubing to the mask.
2. If your mask is equipped with an oxygen port, your physician may request that you apply oxygen directly to your mask.
EN
Clean Filter
Delay Running
10 Minutes Left
Mask Off. Please
check mask fit.
Device Fault E07
Call Provider
SE-DV51
11