Operation - EINHELL GE-SC 35/1 Li Solo Manual De Instrucciones

The height of the handlebar can be set to position
1 or 2 (Fig. 15) during operation. You must then
tighten the quick-release fasteners again.
The same tilt angle must be set on both sides.
Adjusting the scarifi er depth (see Fig. 16)
The scarifi er depth is set with the adjustment me-
chanism. Pull the lever in the direction indicated
by the arrow (see Fig. 16) and adjust to the requi-
red position (0/ 1/ 2/ 3). Make sure that the lever
latches in place correctly!
0 = drive/transport position -3 mm
I = scarifi er depth 3 mm
II = scarifi er depth 6 mm
III = scarifi er depth 9 mm
Charging the battery (Fig. 17/19)
The equipment is supplied without batteries and
without a charger!
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(22) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (21) into the battery
charger (22).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Anl_SA_GE_SC_35_1_Li_Solo_SPK8.indb 34 Anl_SA_GE_SC_35_1_Li_Solo_SPK8.indb 34
GB
Installing the battery (Fig. 18-19)
Open the battery cover. This is done by pressing
both sides of the battery cover as shown in Fig.
18 and opening the cover. Then insert the two
batteries in the mounts as shown in Fig. 19 and
push them forward until the batteries audibly latch
into place.
Note!
Use only batteries which are charged to the same
level. Never combine full and half-full batteries.
Always charge the two batteries simultaneously.
The equipment's operating time depends on the
battery with the lower charge level. The two bat-
teries must always be fully charged before use.
Close the battery cover by swinging it down, and
make sure that it latches in place correctly.
Battery capacity indicator (Fig. 20)
Press the switch for the battery capacity indicator
(Fig. 20/Item A). The battery capacity indicator
(Fig. 20/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.

6. Operation

Caution!
The scarifi er is equipped with a safety switch to
prevent unauthorized use. Directly before starting
up the scarifi er insert the safety plug (Fig. 21/Item
20) and remove the safety plug again when inter-
rupting or terminating your work.
To prevent accidental start-up of the scarifi er, the
push bar (Fig. 22/Item 5) is equipped with a safety
lock-off (Fig. 22/Item 2) which must be pressed
before the lever switch (Fig. 22/Item 1) can be
pressed. The start time for the equipment can
amount to several seconds. If the lever switch is
- 34 -
07.08.2017 11:12:03 07.08.2017 11:12:03