Connecting The Power Cord - Pioneer AVH-X5500BT Manual De Instalación

Connecting the units

Connecting the power cord

Navigation system
26 pin cable (Supplied with navigation unit)
(AVIC-F250 (sold
Insert the 26 pin cable in the direction
separately))
indicated in the figure.
Please contact your dealer to
inquire about the connectable
navigation unit.
Note:
Depending on the kind of vehicle,
the function of 2* and 4* may be
different. In this case, be sure to
connect 1* to 4* and 3* to 2*.
2* 1*
4* 3*
Yellow (2*) Yellow (1*)
Back-up Connect to the constant 12 V
(or accessory) supply terminal.
Red (4*) Red (3*)
Accessory Connect to terminal controlled by
(or back-up) ignition switch (12 V DC).
Orange/white
Connect to lighting switch terminal.
Black (chassis ground)
Connect to a clean, paint-free metal location.
ISO connector
Note:
In some vehicles, the ISO connector may be divided into
two. In this case, be sure to connect to both connectors.
This product
Fuse (10 A)
Antenna input
DAB antenna input
RGB input
(AVH-X3500DAB only)
AUX jack (3.5 ø)
To receive DAB signals,
Use a mini plug
connect a DAB antenna
cable to connect
(AN-DAB1) sold
with auxiliary
separately to the unit.
device.
Connect leads of the same
color to each other.
Speaker leads
White: Front left
White/black: Front left
Gray: Front right
Gray/black: Front right
Rear left  or subwoofer
Green:
Rear left  or subwoofer
Green/black:
Rear right  or subwoofer
Violet:
Rear right  or subwoofer
Violet/black:
Connecting the units
4 m
Microphone (Function of AVH-X5500BT/AVH-X3500DAB/AVH-X2500BT)
Microphone input (Function of AVH-X5500BT/AVH-X3500DAB/AVH-X2500BT)
Wired remote input
Hard-wired remote control adapter can be connected (sold separately).
Violet/white
Of the two lead wires connected to the back lamp, connect the one in which the
voltage changes when the gear shift is in the REVERSE (R) position. This connection
enables the unit to sense whether the car is moving forwards or backwards.
Yellow/black
If you use an equipment with Mute function, wire this lead to the Audio Mute lead on
that equipment. If not, keep the Audio Mute lead free of any connections.
Connection method
1. Clamp the lead.
Note:
· The position of the parking brake switch depends on the vehicle model. For details,
consult the vehicle Owner's Manual or dealer.
Light green
Used to detect the ON/OFF status of the parking brake. This lead
must be connected to the power supply side of the parking brake
switch.
Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
Blue/white (6*)
Blue/white (5*) Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
The pin position of the ISO
connector will differ depending on
the type of vehicle. Connect 5* and
6* when Pin 5 is an antenna control
type. In another type of vehicle,
never connect 5* and 6*.
2. Clamp firmly with
needle-nosed pliers.
Parking brake
switch
Power supply side
Ground side
Notes:
· Change the initial setting of this unit (refer to the Operation Manual).
The subwoofer output of this unit is monaural.
· When using a subwoofer of 70 W (2 Ω) , be sure to connect with Violet
and Violet/black leads of this unit. Do not connect anything to Green
and Green/black leads.
Section
01
3
En