Technical Data - Husqvarna 357XP Manual De Instrucciones

Technical data

Engine
Cylinder displacement, cu.in/cm
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Emissions Durability Period according to California
Air Resources Board, h.
Ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication system
Fuel tank capacity, US pint/litre
Oil pump capacity at 9,000 rpm, ml/min
Oil tank capacity, US pint/litre
Type of oil pump
Weight
Chain saw without bar or chain, empty tanks, lb/kg
Chain/bar
Standard bar length, inch/cm
Recommended bar lengths, inch/cm
Usable cutting length, inches/cm
Pitch, inch/mm
Thickness of drive links, inch/mm
Drive sprocket type/teeth
Chain speed at 133% of maximum engine power
speed, ft/s / m/s.
NOTE! This spark ignition system complies with the Canadian ICES-002 standard.
Recommended cutting equipment for USA
Following is a list of recommended cutting equipment for Husqvarna chain saw models 357XP, 357XPG, 357XP E-tech,
357XPG E-tech, 359, 359 E-tech, 359G and 359G E-tech. These chain saw models equipped with either of the listed
bar and saw chain combination(s), fulfills the requirements according to ANSI B175.1-2000 (Gasoline Powered Chain
Saws - Safety Requirements).
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which
will also achieve kickback reduction.
Chain saw models Husqvarna 357XP, 357XPG, 357XP E-tech, 357XPG E-tech, 359, 359 E-tech, 359G and 359G E-
tech met the kickback performance requirements of ANSI B175.1-2000 when tested with the combinations of bars and
saw chains listed below. The saw chain Husqvarna H30 is also classified as a low kickback saw chain since it met the
requirements for low kickback saw chain outlined in ANSI B175.1-2000. We recommend to use only the listed
combinations of bars and chains for chain saw models Husqvarna 357XP, 357XPG, 357XP E-tech, 357XPG E-tech, 359,
359 E-tech, 359G and 359G E-tech. Other chain saw models may not meet the kickback requirements when equipped
with the listed guide bar and saw chain combinations.
40 – English
Technical data
357XPXPG/E-tech
3
3,45/56,5
1,81/46
1,34/34,0
2700
3,2/4.4 @ 9600
300
NGK BPMR 7A/
Champion RCJ 7Y
0.02/0,5
1,43/0,68
6-17
0,80/0,38
Automatic
12,1/5,5: 357 XP, 357 XP E-tech
12,3/5,6: 357 XPG, 357 XPG E-
tech
15"/38
13-24"/33-61
12-23"/31-58
0.325/8,25
3/8" /9,52
0.050/1,3
0.058/1,5
Rim/7
93.5/28,5
359/G/E-tech
3,60/59,0
1.85/47
1,34/34,0
2700
2,9/3,9 @ 9000
300
NGK BPMR 7A/
Champion RCJ 7Y
0.02/0,5
1,43/0,68
6-17
0,80/0,38
Automatic
12,1/5,5: 359, 359 E-tech
12,3/5,6: 359 G, 359 G E-tech
15"/38
13-24"/33-61
12-23"/31-58
0.325/8,25
3/8" /9,52
0.050/1,3
0.058/1,5
Rim/7
87.3/26,6