Publicidad
Idiomas disponibles
Idiomas disponibles
When the burner is ignited all displays of the regulator light up. The set point display will blink for about 10 seconds. The
value in the upper field of the display (red) indicates the actual value. The value in the lower field of the display (green) indi-
cates the set point currently programmed.
CHANGING THE SET POINT
To change the set point, proceed as follows: - -
display - -
- -
Change the value of set point SP1 using the t and s keys. e
matically – To return to normal display press
* *
The value of SP1 depends on the value set previously in configuration level C111.
SETTING PID PARAMETERS
PID parameters are factory set to standard mean values. The operation of the regulator can be self-adapted to suit the system
by activating the "tunE" function. The regulator will set the PID parameters automatically. To activate the "tunE" function
proceed as follows: - -
- -
With the burner in operation, press
"tunE" stops blinking, the self-adaptation routine has been completed. - -
key for 2 seconds.
* *
The "tunE" function cannot be activated in Manual mode, or when the burner is off.
The PID parameters can be corrected manually from the parameters level, working on the proportional band Pb1, the deri-
vative action time dt and the integral action time rt.
To change parameters Pb1, dt and rt, proceeds as follows: - -
from one parameter to the next, press
t keys. - -
- -
Confirm the changed parameters by pressing
stored automatically. - -
- -
Press
- -
Press PGM to access the next parameter. - -
- -
press
EXIT.
EXIT
DIFFERENTIAL SETTING FOR IGNITION AND SHUTOFF
The regulator allows the selection of an adjustable switching differential that establishes burner ignition and shutoff values.
HYS1 indicates the lower ignition limit, below which the regulator switches the burner to maximum power. HYS3 indica-
tes the upper shutoff limit, above which the regulator switches the burner off. To set HYS1 and HYS3 proceed as follows:
- -
- -
Press the
PGM key to access the parameters level. - -
PGM
displayed (burner ignition differential-stage II), increase or decrease the value using the
parameters by pressing
PGM. - -
PGM
PGM to access the next parameter. - -
PGM
described above. - -
- -
Press
PGM to access the next parameter. - -
PGM
procedure described above.
- -
To return to normal display press
- -
MANUAL/AUTOMATIC MODE
To access "MANUAL" mode, press and hold
ner is in operation. It is deactivated automatically when the burner shuts off. When the LED above the hand symbol is alight,
the regulator is in manual mode and the position of the servocontrol can be changed using the
the front of the regulator indicate whether the servocontrol OPEN or CLOSE command is currently active. Pressing the
key the servocontrol OPENS. Pressing the
for at least 5 seconds. The LED above the hand symbol goes out and the regulator reverts to automatic.
The RWF 40 regulator can be set with the set point interlocked to the external probe. To select this operating mode, proceed
as follows: - -
- -
Connect the required probe as in the wiring diagram. - -
probe the regulator must be set as follows: - -
(XXXX) is displayed, use the
Confirm the change of parameters by pressing
Press
PGM to access the configuration level. When the display reads C112 (XXXX), use the
PGM
(XXXX). Press the
key to set the type of probe (XX3X). - -
mation is not given within 2 seconds the value will be stored automatically.
- -
To return to normal display press
- -
- -
Press
PGM to access the parameters level. - -
- -
PGM
displayed (heating curve gradient), increase or decrease the value using the
by pressing
PGM. - -
- -
If confirmation is not given within 2 seconds the value will be stored automatically.
PGM
- -
To return to normal display press
- -
SETTING PARAMETERS
- -
Press the
EXIT.
EXIT
PGM . - -
- -
When Pb1 is displayed, the value can be increased or decreased using the s and
PGM
PGM. - -
PGM
PGM to access the next parameter. - -
PGM
- -
When rt is displayed, repeat the procedure above. - -
- -
To move from one parameter to the next, press
- -
If confirmation is not given within 2 seconds the value will be stored automatically. - -
- -
When HYS2 is displayed (burner shutoff differential-stage II), repeat the procedure
EXIT.
EXIT
EXIT for at least 5 seconds. Manual mode can only be selected when the bur-
EXIT
key the servocontrol CLOSES. To select automatic mode press and hold
CLIMATIC COMPENSATION
- -
Press the
PGM key to access the configuration level. When the caption C111
PGM
key to access the second figure (XXXX). Use the
PGM. If this is not done within 2 seconds, the value is stored automatically - -
PGM
EXIT. To establish the heating curve, proceed as follows:
EXIT
- -
Press
PGM to move from one parameter to the next. - -
PGM
EXIT.
EXIT
LB1215 BLU 7000.1 - 12000.1 PR / MD B
PGM button to access the user level. SP1* will appear in the lower
PGM
. - -
- -
After a 2 second delay the value set is stored auto-
PGM +
. - -
- -
the caption "tunE*" will blink in the display. – When
PGM
- -
Confirm the computed parameters by pressing the
- -
Press the
PGM button to access the parameters level. - -
PGM
- -
If confirmation is not given within 2 seconds the value will be
- -
When dt is displayed, repeat the procedure described above.
- -
When HYS3 is displayed (upper shutoff differential) repeat the
- -
Change the regulator settings. When using an external
- -
Confirm the changed parameters by pressing
and
pag.21
- -
To return to normal display
PGM . - -
PGM
- -
and
keys. - -
- -
Confirm the changed
and
keys. The LEDS on
key to select the type of probe (XX3X). - -
key to access the second figure
PGM. - -
PGM
- -
When the letter H is
keys. - -
- -
Confirm the changed parameters
- -
To move
When HYS1 is
- -
Press
EXIT
EXIT
- -
- -
- -
If confir-
Publicidad
