Cleaning The Product; Installation Guidelines; Cleaning The Jog Dial - Pioneer MEP-4000 Manual De Instrucciones

Installation guidelines

! Do not place this unit on objects radiating heat, such as an amplifier,
or expose it to a spotlight for an extended period of time, as this may
damage this unit.
! Install this unit away from a tuner or a TV. Otherwise, image distor-
tion or noise may result. Also, image distortion or noise can easily
occur if an indoor antenna is used. In such cases, use an outdoor
antenna or turn off the power of this unit.
! When this unit is used in a loud-sound environment, e.g., near
a speaker, sound skip may occur. Install this unit away from the
speaker or reduce the listening volume.
! Place this unit on a level surface and a stable platform.
! Do not place heavy objects on top of this unit.
Be sure the player, including its audio and power supply cords, does not
touch vibrating materials. Any cause of vibration other than the insula-
tors may cause sound skip. Take special care when using the player
while it is installed in a carrying case.
To assure proper heatdissipation, be
sure to maintain this open space.
To assure proper
heatdissipation, be
sure to maintain
this open space.
Mounting on a rack conforming to EIA
standards
The mount holes on the left and right of this unit's operation panel are
for the 2U (drive unit) + 2U (control unit) size of 19-inch EIA standard
racks. This unit has a maximum depth of 267.6 mm.
! Secure this unit with screws (not supplied) matching the rack.
! Do not install this unit directly above a power amplifier. Heat radiat-
ing from the power amplifier may damage this unit. Also, noise (hum
noise, etc.) may be generated.
! When transporting this unit, remove it from the rack. Transporting
this unit without removing it from the rack may damage this unit.
! If you transport this unit without removing it from the rack, make
sure vibration or shock is not applied to this unit.
Transporting this unit
 Never move this unit during playback
During playback, discs rotate at very high speeds; never lift or move this
unit during this time to prevent scratches or other damage to discs.
 When moving this unit
When moving this unit, always remove any discs that have been loaded,
and turn off the power. Moving this unit with a disc loaded could result
in damage to the disc or unit.
About carrying cases
If this unit is placed in a carrying case, take precautions to prevent any
pressure from being exerted on the surface of the jog dial.
12
En
Do not allow contact with vibrating
surfaces.
To assure proper
heatdissipation, be
sure to maintain
this open space.

Cleaning the product

Under normal circumstances, wipe it with a dry cloth. For hard-to-
remove stains, soak a soft cloth in a neutral detergent diluted with 5 to
6 times of water, wring it thoroughly, wipe off the stains, and wipe the
surface with a dry cloth again. Do not use alcohol, thinner, benzene, or
insecticide, as these may peel off the printed label or the coated film.
Avoid leaving rubber or vinyl products in contact for an extended period
of time, as this may also damage the surface of the cabinet. When using
chemical-impregnated wipes, etc., read the cautions carefully.
Unplug the power plug from the AC outlet when cleaning this unit.

Cleaning the Jog Dial

To clean the jog dial, wipe with a polishing or a soft, dry cloth. For stub-
born dirt, moisten a soft cloth with a weak solution of neutral detergent
(diluted in 5 to 6 parts water), wring the cloth well, and wipe away the
dirt. Use a dry cloth to wipe the surface dry. Applying alcohol, paint
thinner, benzene, insecticides, or other stringent substances to the jog
dial may cause the markings or finishing of the dial to peel or become
discolored, and the use of any such substances should accordingly be
avoided.