Microlife IR 210 Manual Del Usuario página 5

Tabla de contenido

Publicidad

2. Press the M-button 3 to either turn the beeper on or off. The beeper
is activated when the beeper icon BR is shown without a cross.
When the beeper setting has been chosen, press the
START/IO button 6 to enter the «ready for measuring»
mode; otherwise the device automatically switches to ready
for measuring after 10 seconds 9.
6. Changing between Body and Object Mode
1. Press the START/IO button 6. The display 2 is activated to
show all segments for 1 second.
2. The default mode is body mode. Press the MODE button 4 to
switch to object mode. For switching back to body mode, press
the MODE button again.
7. Directions for Use
Measuring in body mode
Important: Before each measurement, fit a new undamaged probe
cover CK on the measuring sensor 1. Failure to do so will result in
incorrect temperature measurements. How to correctly fit a new
probe cover CL is pictured at the beginning of this instruction.
1. Press the START/IO button 6. The display 2 is activated to
show all segments for 1 second.
2. When the «°C» or «°F» icon is flashing, a beep sound is heard
and the thermometer is ready for measuring 9.
3. The probe LED light is activated and will keep flashing.
4. Straighten the ear canal by pulling the ear up and back to give
a clear view of the eardrum.
 For children under 1 year; pull the ear straight back.
 For children of 1 year to adult; pull the ear up and back.
Also refer to the short instructions at the front.
5. While gently pulling the ear, insert the probe snugly into the ear
canal.
6. The probe LED light will stop flashing (stays illuminated) and
«good» will be displayed on the LCD, when the measuring
sensor detects an appropriate position.
7. Immediately press the START/IO button 6. Release the button
and wait for the beep sound. This indicates the end of the
measurement.
8. Remove the thermometer from the ear canal. The display shows
the measured temperature AK.
9. Replace the probe cover CK before starting a new measurement.
IR 210
10.For the next measurement wait until the «°C»/«°F» icon is
flashing and follow steps 5-7 above.
11.Press and hold the START/IO button 6 for 3 seconds to turn
off the device; otherwise the device will automatically switch off
after approx. 60 seconds.
Measuring in object mode
Important: Remove the probe cover before each measurement in
object mode. Failure to do so will result in incorrect temperature
measurements.
1. Press the START/IO button 6. The display 2 is activated to
show all segments for 1 second.
2. Press the MODE button 4 to switch to object mode.
3. Aim the thermometer at the center of the object you want to
measure with a distance of no more than 5 cm. Press the
START/IO button 6. After 1 second a long beep will verify the
completion of measurement.
4. Read the recorded temperature from the LCD display.
5. For the next measurement wait until the «°C»/«°F» icon is
flashing and follow steps 3-4 above.
NOTE:
 Patients and thermometer should stay in similar room
condition for at least 30 minutes.
 To ensure accurate readings, wait at least 30 sec. after 3-5
continuous measurements.
 It is essential that a new undamaged probe cover CK is
used for each measurement. Therefore, this device reminds
the user to take off the used probe cover when turning off the
device. The «probe cover» icon BN is displayed and the probe
LED light will flash for 3 seconds. For cleaning, follow the
instructions in the «Cleaning and Disinfecting» section.
 After cleaning the measuring sensor 1 with alcohol, wait 5
minutes before taking the next measurement, in order to allow
the thermometer to reach its operating reference temperature.
 10 short beeps and a red LCD backlight alert the patient that he/
she may have a temperature equal to or higher than 37.5 °C.
 For an infant, it is best to have the child lying flat with his/her head
sideways so the ear is facing upwards. For an older child or adult,
it is best to stand behind and slightly to the side of the patient.
 Always take the temperature in the same ear, since the temper-
ature readings may be different from ear to ear.
EN
4

Publicidad

Tabla de contenido
loading

Tabla de contenido