Cleaning Carpet; Picking Up Spills; Cleaning Bare Floors - Hoover SteamVac F5906 Guia Del Propietario

If rinsing is desired, be careful not to
over-wet the carpet or upholstery.
Allow time for carpet or upholstery to
dry completely between cleaning and
rinsing. To rinse, follow the same proce-
dure for cleaning only using hot tap
water with no detergent in the upper
clean solution tank.
c. Empty tanks, rinse with clear water
and let air dry. Rinse the solution tank
cap and recovery tank lid and let air dry.
3-1
d. Remove debris from recovery tank fil-
ter and rinse with clean water.
Note: If the filter must be removed for
cleaning, it is easier to replace if the fil-
ter is wet.
e. If desired, vacuum thoroughly after
carpet has completely dried. This will
help reduce any shading left by the
deep cleaner's brushes.
5. Squeeze trigger to release cleaning
solution and slowly push deep cleaner
forward (equals one wet stroke).
6. Continue to squeeze trigger and slow-
ly pull deep cleaner back toward you
(second wet stroke). Release trigger and
slowly push deep cleaner forward over
area just sprayed with solution (dry
stroke). Then slowly pull deep cleaner
back toward you without squeezing trig-
ger (dry stroke).
7. Overlap strokes by 1 inch to help pre-
vent streaking.
Keep nozzle flat on floor for both forward
and reverse strokes.
8. For heavily soiled areas, repeat steps
5-7.
Note: To avoid saturating carpet, do
not use more than 4 wet strokes over
one area. Always end with dry strokes.
It is best to alternate wet and dry strokes
as described above.
For best cleaning results and to aid in
faster drying of carpet, end with more
dry strokes. (Continue using dry strokes
until little water is visible passing through
the recovery tank lid.)
Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see "Automatic
shut-off", page 7).
When finished cleaning, follow "After
cleaning" instructions on pages 9 and
10.
10
To clean nozzle
If lint or other debris becomes lodged in
nozzle, do not attempt to remove
nozzle cover.
Pour one to two cups of clear water on a
non-carpeted floor. Do not pour water
onto a wood floor.
Pick up water with your 'SteamVac' deep
cleaner. Repeat as necessary until
debris is flushed out of nozzle.
To clean the outside of the machine,
wipe off dirt with a cloth dampened in
warm water and mild detergent. Do not
use solvent or petroleum based prod-
ucts to clean the machine.

Picking up spills

Your HOOVER SteamVac deep cleaner
may also be used to pick up small liq-
uid spills (1 gallon or less, never to
exceed 1/4 inch in depth) on carpet,
upholstery, or bare floors.
For best results, pick up spills immedi-
ately by placing the stair/upholstery noz-
zle just above the spill and suction up
any residue on top of the carpet. If the
spill remains, place either the stair/
upholstery nozzle or floor nozzle with
brushes turned OFF in front of the spill,
pull the nozzle very slowly over the spill
initially with suction only. Repeat with spray
and suction.
When picking up spills on bare floors,
use only the floor nozzle with the bare
floor attachment in place and speed
selector in the OFF position (this will help
prevent spreading the spill).
If a spot is left, the stair/upholstery nozzle is
generally more effective for removing it.
Although no cleaning solution can com-
pletely remove all spots, they can be treat-
ed by following the instructions provided by
the manufacturer of the carpet, upholstery,
or bare floor surface being cleaned.
Do not use the SteamVac deep cleaner
to pick up flammable or combustible liq-
uids or chemicals.
When finished, follow "After cleaning"
instructions on pages 9 and 10.
Carpet Cleaning
Read "Before you begin cleaning"
instructions on page 9.
1. Fill clean solution tank (upper tank)
with HOOVER Deep Cleansing™
Detergent according to instructions on
pages 7 and 8.
3-2
2. Move speed selector to LO for gen-
tle cleaning or Hl for normal cleaning.
3. Dry hands and plug cord into a prop-
erly grounded outlet.
Do not clean over floor electrical out-
lets.
4. To avoid walking on damp carpet,
start at the end of the room farthest from
the door or path to sink where tanks will
be emptied and filled.
Step on handle release pedal and lower
handle to operating position; turn deep
cleaner ON.

Cleaning bare floors

How to attach bare floor
attachment
(available at addi-
tional cost)
Disconnect deep cleaner from electri-
cal outlet.
To prevent possible leaking, remove
clean solution tank and recovery tank
before positioning bare attachment.
Refer to Fig. 2-9 to remove clean solu-
tion tank. Set tank aside (do not set tank
on furniture).
Refer to Fig. 2-16 to remove recovery
tank.
With handle in upright position, tilt clean-
er back so that handle rests on the floor.
3-3
A
B
With foam strip (A) (located under the
netting) in position as shown, place
attachment on front of nozzle (B).
Make sure arrow on end of attachment
points in the direction as shown.