Lubrication And Cleaning - Virutex RZ270S Manual De Instrucciones

the machine with the symbol V to facilitate replacement.
Ensure that when the cover is replaced, the clamps of the
brush holder do not pinch the cable.
Screw cover P back into place. We advise that you leave
the machine on but without using it for 15 minutes so
that the brushes can self-adjust.
If you observe any burning or protruding of
the collector, take it to a VIRUTEX technical
service outlet to be repaired. Never use
emery paper for this operation.

14. LUBRICATION AND CLEANING

The machine comes fully lubricated from the factory and
does not require special care.
Always carefully clean the machine after use and periodically
oil the guides Z (Fig. 5), making sure they are never left dry.
Keep the power cable in perfect condition.
Keep the machine's vent and cooling openings clean and
unobstructed.
15. NOISE AND VIBRATION LEVEL
The noise and vibration levels of this device have been
measured in accordance with European standard EN 60745-
2-19 and EN 60745-1 and serve as a basis for comparison
with other machines with similar applications.
The indicated vibration level has been determined for the
device's main applications and may be used as an initial value
for evaluating the risk presented by exposure to vibrations.
However, vibrations may reach levels that are quite different
from the declared value under other application conditions,
with other tools or with insufficient maintenance of the
electrical device or its accessories, reaching a much higher
value as a result of the work cycle or the manner in which
the electrical device is used.
Therefore, it is necessary to establish safety measures to
protect the user from the effects of vibrations, such as
maintaining both the device and its tools in perfect con-
dition and organising the duration of work cycles (such as
operating times when the machine is subjected to loads,
and operating times when working with no-load, in effect,
not in use, as reducing the latter may have a considerable
effect upon the overall exposure value).
16. WARRANTY
All VIRUTEX power tools are guaranteed for 12 months
from the date of purchase, excluding any damage which is
a result of incorrect use or of natural wear and tear on the
machine. All repairs should be carried out by the official
VIRUTEX technical assistance service.
17. RECYCLING ELECTRICAL EQUIPMENT
Never dispose of electrical equipment with domestic waste.
Recycle equipment, accessories and packaging in ways that
minimise any adverse effect on the environment. Comply
with the current regulations in your country.
Applicable in the European Union and in European countries
10
with selective waste collection systems:
If this symbol appears on the product or in the accompanying
information, at the end of the product's useful life it must
not be disposed of with other domestic waste.
In accordance with European Directive 2002/96/EC, users
may contact the establishment where they purchased the
product or the relevant local authority to find out where
and how they can take the product for environmentally
friendly and safe recycling.
VIRUTEX reserves the right to modify its products without
prior notice
F R A N Ç A I S
SCIE ARASANTE RZ270S
Important
Avant d'utiliser la machine, lisez attentivement
ce MANUEL D'INSTRUCTIONS et la BROCHURE
D'INSTRUCTIONS GÉNÉRALES DE SÉCURITÉ
qui vous sont fournis avec cette machine.
Assurez-vous de bien avoir tout compris avant
de commencer à travailler sur la machine.
Gardez toujours ces deux manuels d'instructions
à portée de la main pour pouvoir les consulter,
en cas de besoin.
1. INSTRUCTIONS DE SÉCURITÉ POUR
LE MANIEMENT DE LA SCIE ARASANTE
Avant d'utiliser la machine, lire attenti-
vement la BROCHURE DES INSTRUCTIONS
GÉNÉRALES DE SÉCURITÉ jointe à la docu-
mentation de la machine.
1. Vérifier avant de brancher la machine si la tension
d'alimentation correspond à celle indiquée sur la plaque
des caractéristiques.
2. Attention, toujours maintenir les mains éloignées de la
zone de travail.
3. Ne pas prendre la machine par le dessous quand elle
est en marche.
4. Vérifier s'il y a des clous sur la surface à couper et, si c'est
le cas, les retirer avant de commencer à travailler.
5. Contrôler si la machine recule librement sans être bloquée.
Ne jamais bloquer le mécanisme de recul.