Lubrication And Cleaning; Données Techniques - Virutex FC16S Manual De Instrucciones

18. CHANGING THE BRUSHES
Make sure that the machine is dis-
connected from the mains before any
handling is done.
- The brushes should be changed when they are a
minimum of 5 mm long. To do this, dismount the
switch box "F1" (Fig. 11), removing the screws "G1"
which fasten it.
Remove the plugs "H1" which fasten the brushes
"I1" and replace with new original VIRUTEX ones,
checking that they slide smoothly on the inside of
the guides. Ensure when mounting the switch box
"F1" again that the cables are properly positioned
inside. It is advisable to leave the machine running
for a few minutes after a change of brushes. Take
advantage of the change of brushes to check the
state of the collector. If this shows signs of burns or
wear and tear, it is advisable to take it to VIRUTEX
technical service for repair.

19. LUBRICATION AND CLEANING

- Before trimming the first fitting, lubricate the depth
guide columns (Gp, Fig. 2) and side columns (Gt, Fig.
2), with a lightly oiled cloth, in order to smooth the
two movements. It is important always to clean the
machine carefully after use, with a dry air jet.
Always keep the power supply cable in perfect
condition.
20. OPTIONAL TOOLS AND ACCESSORIES
- Bits available for the FC16S mortising trimmer:
NUMBER
1640127
1640150
1640128
1640129
1640130
1640131
1640132
1640140
21. NOISE AND VIBRATION LEVEL
The noise and vibration levels of this electrical device
have been measured according to the European
standard EN50144.
The noise level in the workplace can exceed 85 dB(A),
in which case it is necessary for the user to take noise
protection measures.
10
EXT. DIAM. HEIGHT
16 mm 13.5 mm
17 mm 13.5 mm
18 mm 13.5 mm
21 mm 13.5 mm
23 mm 13.5 mm
25 mm 13.5 mm
30 mm 13.5 mm
Drilling bit Ø 24
22. WARRANTY
All VIRUTEX power tools are guaranteed for 12 months
from the date of purchase, excluding any domage
which is a result of incorrect use or of natural wear
and tear on the machine.
All repairs should be carried out by the official
VIRUTEX technical assistance service.
VIRUTEX reserves the right to modify its products
without prior notice.
F R A N Ç A I S
MORTAISEUSE FC16S
(FIGURES EN PAGE 33)
Important
Avant d'utiliser la machine, lisez atten-
tivement ce MANUEL D'INSTRUCTIONS
et la BROCHURE D'INSTRUCTIONS
GÉNÉRALES DE SÉCURITÉ qui vous
sont fournis avec cette machine. As-
surez-vous de bien avoir tout compris
avant de commencer à travailler sur
la machine.
Gardez toujours ces deux manuels
d'instructions à portée de la main
pour pouvoir les consulter, en cas de
besoin.
1. DONNÉES TECHNIQUES
Moteur universel...................................50/60 Hz
Puissance..............................................1.100 W
Vitesse à vide...................................23.000 t/min
Niveau de pression acoustique
continu équivalent pondéré.........................87 dB
Niveau de puissance acoustique..........100 dB (A)
Niveau habituel vibrations (main/bras)....<2,5 m/s
Diamètre maximum de Fraise....................30 mm
Profondeur maximum de fraisage.........0-125 mm
Largeur maximum de fraisage............diam. fraise
Longueur maxi. de
fraisage.........................177 mm + diamètre fraise
Ouverture maximum des étaus................190 mm
Serrage minimum des étaus......................13 mm
Déplacement latéral de la fraise sur
l'épaisseur de la porte............................+/- 15 mm
Poids..........................................................14 kg
2