Before Starting The Equipment - EINHELL TE-ID 1050/1 CE Manual De Instrucciones

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making adjust-
ments to the equipment.
5.1. Fitting the additional handle (Fig. 2-3/
Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do
not use the tool without the additional handle.
The additional handle (8) is secured to the ham-
mer drill by a clamp. During the handle clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
•
The supplied additional handle (8) must
first be fitted. To do this, the clamp must be
opened by turning the handle until it is wide
enough for the additional handle to be slid
over the chuck (1) and on to the hammer drill.
•
After you have positioned the additional
handle (8), turn it to the most comfortable
working position for you.
•
Now turn the handle in the opposite direction
again until the additional handle is secure.
•
The additional handle (8) is suitable for both
left-handed and right-handed users.
5.2 Fitting and adjusting the depth stop
(Fig. 4/Item 2)
•
Undo the thumb screw (a) on the additional
handle (8) and insert the depth stop (2) in the
hole of the additional handle.
•
Set the depth stop and retighten the thumb
screw.
•
Now drill the hole until the depth stop touches
the workpiece.
5.3 Fitting the drill bit (Fig. 5)
Always pull the power plug before making adjust-
ments to the equipment.
•
Release the depth stop as described in 5.2
and push it towards the additional handle.
This provides free access to the chuck (1).
•
This hammer drill is fitted with a keyless
chuck (1).
•
Open the chuck (1). The drill bit opening must
be large enough to fit the drill bit into.
•
Select a suitable drill bit. Push the drill bit as
far as possible into the chuck opening.
•
Close the chuck (1). Check that the drill bit is
GB
•
6. Operation
6.1 ON/OFF switch (Fig. 6/Item 5)
•
•
•
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
To switch off :
Press the ON/OFF switch (5) briefl y.
6.2 Adjusting the speed (Fig. 6/Item 5)
You can infi nitely vary the speed whilst using the
tool.
•
•
•
•
Tip: Start drilling holes at low speed. Then increa-
se the speed in stages.
Benefi ts:
•
•
6.3 Preselecting the speed (Fig. 7/Item 6)
The speed controller (6) enables you to defi ne the
maximum speed.
•
www.sidirika-nikolaidi.gr
•
- 17 -
secure in the chuck (1).
Check at regular intervals that the drill bit or
tool is secure (pull the mains plug).
First fit a suitable drill bit into the tool (see
5.3).
Connect the mains plug to a suitable socket.
Position the drill in the position you wish to
drill.
Select the speed by applying a greater or les-
ser pressure to the ON/OFF switch (5).
Select the correct speed: The most suitable
speed depends on the workpiece, the type of
use and the drill bit used.
Low pressure on the ON/OFF switch (5): Lo-
wer speed (suitable for: small screws and soft
materials)
Greater pressure on the ON/OFF switch (5):
Higher speed (suitable for large/long screws
and hard materials)
The drill bit is easier to control when starting
the hole and will not slide away.
You avoid drilling messy holes (for example
in tiles).
Set the speed controller (6) to the required
position.
With the On/Off switch (5) pressed right in,