Fein 7 129 Serie Manual De Instrucciones página 18

OBJ_BUCH-0000000213-001.book Page 18 Wednesday, August 12, 2015 8:19 AM
en
18
Emission values for vibration
Vibration
Classification of FEIN application
tools according to vibration class
VC0
VC1
VC2
VC3
VC4
VC5
a
K
* These values are based on a work cycle consisting of no-load
and full-load operation of the same duration.
For information on the vibration class assigned to the application
tool, please see the enclosed data sheet 3 41 30 213 06 2.
Operating Instructions.
Changing the tool (see page 5)
Do not use accessories not specifically intended and
recommended for this power tool by FEIN. The use of non-
original FEIN accessories can lead to overheating of the
power tool and destroy it.
When changing application tools with sharp cutting
edges, use cover 3 21 74 011 00 0 to protect your-
self against hand injuries.
Firmly press in the fastening element to the stop.
Then lock the clamping lever.
Protect your hand and fingers against bruising when
locking the clamping lever. The clamping lever
snaps back vigorously by means of spring force.
Handling the battery.
Operate and charge the battery only within the battery
operating-temperature range of 0°C – 45°C (32°F –
113°F). At the beginning of the charging procedure, the
battery temperature must be within the battery operat-
ing-temperature range.
LED indicator Meaning
1 – 4 green Percentage of
LED charge condi-
tion
Continuous Battery is
red light almost empty
Red flashing Battery is not
light ready for
operation
The real percentage of the battery charge condition is
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor prior
to the battery being deep discharged.
Additional operating instructions.
Weighted
The self-start prevention lock prevents the power tool
acceleration*
from automatically starting when the battery is inserted
2
while the on/off switch is set to on.
< 2.5 m/s
Before using, sharpen used and even new cutter blades
2
< 5 m/s
with the cleaning block.
2
< 7 m/s
The symptom for worn blades is a clearly increased feed
2
< 10 m/s
force at lower working progress.
2
< 15 m/s The application tool can be offset in 30° steps and fas-
tened in the most favourable working position.
2
> 15 m/s
Guide straight, bent or offset cutter blades at a right angle
2
1.5 m/s
to the window flange (see page 7-8, Cutter blades A – D).
For U-shaped cutter blades, pay attention that the
traverse of the cutter blade is led parallel to the window
pane of the vehicle (see page 8, Cutter blades E – F).
The scraper knife is used for cutting back bond remain-
ders on the window flange or the pane. Before re-bond-
ing the vehicle window, cut back the remaining bead to a
height of approx. 2 mm (see page 8, Cutter blades G).
Repair and customer service.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air.
For storage of the power tool, remove the application
tool, shut the clamping lever, and then press in the fasten-
ing element.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
If required, you can change the following parts yourself:
Fastening element, application tools
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
Activity
a part of the accessories described or shown in this
Operation Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
Charge battery
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Bring the battery into
Technical documents at: C. & E. Fein GmbH, C-DB_IA,
the battery operating-
D-73529 Schwäbisch Gmünd
temperature range,
then charge
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insulate
the terminals with tape as a protective measure against
short-circuiting.
Guide the power tool toward the work piece only
when switched on.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.