Publicidad
Enlaces rápidos
LED CANOPY LIGHT
Models: 65-623, 65-624, 65-625, 65-626, 65-627,
65-628, 65-629, 65-630, 65-631, 65-632
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
WARNING: Risk of Fire or Electric Shock
• To avoid damage, falling, electric shock or fire, do not modify the fixture or replace
accessories without confirming with the supplier first.
• Only authorized, qualified personnel should install this fixture and should follow the
owner's manual. Any improper installation might cause failure, electric shock, fire or
other injury, damage or hazard. The LED canopy light must be installed with UL listed
liquid-tight conduit fittings.
• Disconnect power before installation or any maintenance of the fixture.
• Do not dismantle the fixture without the supplier's authorization.
• Do not touch the power supply when the fixture is operating.
• The electrical fitting must be installed by a licensed electrician.
• For use in environments where an accumulation of non-conductive dust on the
fixture may be expected.
• Use min 75˚ C supply.
IMPORTANT: This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and operation of the product
and the hazards involved.
INSTALLATION: Ceiling Mount
1. Disassemble the driver box cover. Figure 1-1
2. Loosen the 3/4" plug on the driver box cover with a screwdriver. Figure 1-2
3. Drill holes on the ceiling according to the fit plate. Figure 1-3
4. Fix the driver box cover on the ceiling. Figure 1-4
5. Attached the safety cord to the hook inside the back of the driver box once mounted. Figure 1-5
6. Connect the input line and ground; If the fixture is equipped with sensor, adjust !he sensor settings. Take relevant waterproof
measures after the wires are connected. Figure 1-6
7. Align the drive box cover with !he metal shrapnel inside the drive box and press upward to fasten it together. Figure 1-7
8. Lock the four screws, the product is installed. Figure 1-8
Figure 1-1
Figure 1-5
© Copyright 2020 Satco Products, Inc. 1/20
Figure 1-2
Figure 1-6
1
Figure 1-3
Figure 1-7
25W: 65-623
65-624
40W: 65-625
65-626
55W: 65-627
65-628
75W: 65-629
65-630
100W: 65-631
65-632
Figure 1-4
Figure 1-8
Satco Products, Inc.
Brentwood, NY 11717
Publicidad
Manuales relacionados para Satco NUVO 65-623
Resumen de contenidos para Satco NUVO 65-623
- Página 1 8. Lock the four screws, the product is installed. Figure 1-8 Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4 Figure 1-8 Figure 1-5 Figure 1-6 Figure 1-7 Satco Products, Inc. © Copyright 2020 Satco Products, Inc. 1/20 Brentwood, NY 11717...
- Página 2 INSTALLATION: Pendant Mount 1. Disassemble the driver box cover. Figure 2-1 2. Loosen the 3/4" plug on the driver box cover with a screwdriver. Figure 2-2 3. Fix the driver box cover on the 3/4 tube. Figure 2-3 4. Attached the safety cord to the hook inside the back of the driver box once mounted. Figure 2-4 5.
- Página 3 PARAMETER SETTING BY REMOTE CONTROL IN MANUAL OF RC-100 Wiring Diagrams. BRl823-B-D wiring with dimming ballast or LED driver. BRl823-B-D wiring with non-dimming ballast or LED driver. Dimming Driver Non-Dimming Driver Structure of Motion Sensor Settings By selecting the combination on the DIP switch, motion sensor data can be set precisely for each specific application. Detection area Daylight Sensor Detection area can be reduced by...
- Página 4 LUMINARIA LED TIPO UFO PARA ÁREAS ALTAS ESPAÑOL: Modelos: 65-623, 65-624, 65-625, 65-626, 65-627, INSTRUCCIONES DE INSTALACIÓN Y SEGURIDAD 65-628, 65-629, 65-630, 65-631, 65-632 IMPORTANTE: Lea esto antes de instalar el accesorio. Consérvelo para referencia futura. SEGURIDAD: Riesgo de incendio y descarga eléctrica •...