Electrical Connection; Accessories - DeWalt DW718 Serie Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

• TURN OFF THE MACHINE and allow the blade to come to a complete stop before
raising the arm and prior to cleaning the blade area, removing debris in the path of the
blade, before servicing or adjusting tool. A moving blade can cause serious injury.
• PROPERLY SUPPORT LONG OR WIDE WORKPIECES. Loss of control of the
workpiece can cause injury.
• NEVER cross arms in front of blade while using tool. Always make a dry run
(unpowered) before making a finish cut so that you can check the path of the blade or
severe personal injury may result.
• ADDITIONAL INFORMATION regarding the safe and proper operation of power
tools (i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner
Avenue, Cleveland, OH 44115-2851 (www.powertoolinstitute.com). Information is also
available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-
3201. Please refer to the American National Standards Institute ANSI 01.1 Safety
Requirements for Woodworking Machines and the U.S. Department of Labor OSHA
1910.213 Regulations.
CAUTION: Do not connect unit to electrical power source until complete instructions are
read and understood.
WARNING: Always wear proper personal hearing protection that conforms to
ANSI S12.6 (S3.19) during use. Under some conditions and duration of use, noise from
this product may contribute to hearing loss.
WARNING: NEVER MAKE ANY CUT UNLESS THE MATERIAL IS SECURED ON
THE TABLE AND AGAINST THE FENCE.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects or other
reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks that are specially designed to
filter out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding,
drilling, and other construction activities. Wear protective clothing and wash
exposed areas with soap and water. Allowing dust to get into your mouth, eyes,
or lay on the skin may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause
serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved
respiratory protection appropriate for the dust exposure. Direct particles away from face
and body.
For your convenience and safety, the following warning labels are on your miter saw.
ON MOTOR HOUSING:
WARNING: FOR YOUR OWN
SAFETY,
READ
INSTRUCTION
MANUAL BEFORE OPERATING SAW.
WHEN
SERVICING,
USE
ONLY
IDENTICAL REPLACEMENT PARTS.
DO NOT EXPOSE TO RAIN OR USE IN
DAMP LOCATIONS.
ALWAYS WEAR EYE PROTECTION.
ON MOVING FENCES:
ALWAYS ADJUST FENCE PROPERLY BEFORE USE. Clamp small pieces before cut-
ting. See manual.
ON GUARD: DANGER – KEEP AWAY FROM BLADE.
ON UPPER GUARD: PROPERLY SECURE BRACKET WITH BOTH
SCREWS BEFORE USE.
ON TABLE: (2 PLACES)
ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE USE.
KEEP HANDS 6" FROM PATH OF SAW BLADE.
NEVER PERFORM ANY OPERATION FREEHAND.
NEVER CROSS ARMS IN FRONT OF BLADE.
THINK! YOU CAN PREVENT ACCIDENTS.
DO NOT OPERATE SAW WITHOUT GUARDS IN PLACE.
TURN OFF TOOL, KEEP SAW HEAD DOWN AND WAIT FOR SAW TO
STOP BEFORE MOVING HANDS, WORKPIECE OR CHANGING
SETTINGS.
UNPLUG TOOL BEFORE CHANGING BLADE, MOVING OR SERVICING
UNIT.

Electrical Connection

Be sure your power supply agrees with the nameplate marking. 120 volts, AC means that
your saw will operate on alternating current. The switch is suseptible to failure if direct
current is used. A voltage decrease of 10 percent or more will cause a loss of power and
overheating. All D
WALT tools are factory tested. If this tool does not operate, check the
E
power supply.

Accessories

Recommended accessories for use with your tool are available for purchase from your local
dealer or authorized service center. If you need assistance in locating any accessory for
your tool, please contact D
WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD
E
21286, call 1-800-4-D
WALT (1-800-433-9258) or visit our website www.dewalt.com.
E
WARNING: Since accessories, other than those offered by D
tested with this product, use of such accessories with this tool could be hazardous. To
reduce the risk of injury, only D
WALT, recommended accessories should be used with
E
this product.
Optional Accessories
The following accessories, designed for your saw, may be helpful. In some cases, other
locally obtained work supports, length stops, clamps, etc., may be more appropriate. Use
care in selecting and using accessories.
Laser Guide System: DW7187
Laser is available at extra cost from D
ment retailer. Instructions for installation are included with the accessory. Read and
follow all directions for safe installation and use.
Extension, Work Support: DW7080
Used to support long overhanging workpieces, the work support is user assembled.
Your saw table is designed to accept two work supports; one on each side.
Adjustable Length Stop: DW7051
Requires the use of one work support (see drawing). It is used to make repetitive cuts
of the same length from 0 to 42".
4 4
WALT, have not been
E
WALT Service Centers and your home improve-
E

Publicidad

Tabla de contenido
loading

Tabla de contenido