Connecting To Network - Pioneer X-HM82-S Manual De Instrucciones

Connecting to network

The following is one example of how to connect to a network.
For other connections, please refer to the attached Operating Instructions (CD-ROM)
Connecting this receiver using
wired LAN
1. Be sure your router supports DHCP server
function.
2. Use the LAN cable to connect this receiver
and your router.
3. Plug the power cord into an AC outlet.
Press u STANDBY/ON.
B: Connecting to a router with WPS-
PBC function
1. Be sure the LAN cable is not connected to
the receiver.
2. Plug the power cord into an AC outlet.
Press u STANDBY/ON.
3. Press NET SERVICEd SETUP on the
remote control.
4. Select Network Settingd WPS.
5. Usei/jto select PBC (Push Button
Configuration) and then press ENTER.
6. Press the WPS button on the router.
If the connection does not succeed, refer
to Operating Instructions (CD-ROM) (page
44) and redo the setting again.
PBC (Push Button Configuration)
• The wireless connection setting is
automatically configured by pressing
the WPS button on the WPS compatible
wireless LAN device.
Connecting this receiver using
wireless LAN
A: Connection settings using an iOS
device (with iOS 5.0 or later)
You can apply iPod/iPhone/iPad (iOS device
with iOS ver 5.0 or later)'s Wi-Fi settings to
this receiver.
1. Be sure the LAN cable is not connected to
the receiver. Unlock your iPod/iPhone/iPad.
2. Plug the power cord into an AC outlet.
Press u STANDBY/ON.
3. Unlock your iPod/iPhone/iPad. Check that
the Wi-Fi mark is displayed on the iOS
device screen.
Share Wi-Fi Settings?
C: Connecting to a router without
WPS-PBC function
1. Be sure the LAN cable is not connected to
the receiver.
2. Plug the power cord into an AC outlet.
Press u STANDBY/ON.
3. Press NET SERVICEdSETUP.
The Initial Setup screen is shown on the
display.
4. Select Network Setting dNetwork
Configuration.
5. Usei/jto select Wireless, then press
ENTER.
Network Configuration
Wired
Wireless
6. Usei/jto select Auto, then press
ENTER.
Wireless
Auto
Manual
Wireless Accessory Configuration
Web Control
7. Use i/j to select the available wireless
network you want to connect to, then press
ENTER.
The receiver will only display the names of
2.4 GHz wireless LAN routers (SSID).
"Pioneer" is a trademark of Pioneer Corporation, and is used under license.
4. Press iPod/USB on the remote control.
Connect the iOS device to the USB
terminal.
5. Press SETUP.
6. Select Network Setting d Network
Configuration d Wireless d iOS Device
and then press ENTER.
7. Tap Allow on iPod/iPhone/iPad.
The Wi-Fi settings of your iPod/iPhone/
iPad are applied to the receiver.
Ignore
Availabl Available Wireless Networks Avai
XXXXXXXX XXXX XXXXXXXXX
8. Use i/j/k/l to enter the Pass Phrase or
WEP Key.
A
[REPEAT]
[CLEAR]
k/l : Moves the adjusting digit.
i/j : Changes displayed character.
REPEAT: Switches character types.
CLEAR: Deletes one character at a time.
9. Use i/j to select DHCP On, then press
ENTER.
Select Don't Use Proxy Server, then
press ENTER.
Network Configuration
DHCP On
DHCP Off
10. In order to activate the setup, press
ENTER .
Refer to Operating Instructions (CD-ROM)
(Connection method 4 | Have the receiver
automatically detect the wireless LAN
router and perform settings on page 33)
and redo the setting again.
© 2015 Onkyo & Pioneer Corporation.
Share Wi-Fi Settings?
Ignore
lable Wi e Wirele reless N ss Netwo etworks rks
XXXXX X
Enter Password
Change Text
Delete One Character
All rights reserved.
5
En