Tl260Gs/Gs2060; Installation With Pc1616/1832/1864 Control Panel - DSC TL260GS Manual De Instrucciones

Comunicador de alarma de doble vía ethernet/internet y gsm/gprs comunicador de alarma inalámbrico gsm/gprsgsm/gprs
Ocultar thumbs Ver también para TL260GS:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

TL260GS/GS2060

Ethernet Cable
The following requirements for installation of CAT5 Ethernet cable must be observed for correct operation of connected equipment.
• Do NOT strip off cable sheathing more than required for proper termination.
• Do NOT kink or knot cable.
• Do NOT crush cable with cable ties.
• Do NOT splice cable.
• Do NOT bend cable at right angles or make any other sharp bends.
NOTE: All cable bends must have a minimum 5cm (2") radius.
• Do NOT untwist CAT5 pairs more than 1.2cm (½")
• Do NOT exceed maximum 15cm (6") from center of ferrite to T-Link Network Connector.

Installation with PC1616/1832/1864 Control Panel

1. Assemble the Communicator
• Remove the four white plastic standoffs from their bag in
the Communicator kit.
• Insert the standoffs in through the back (the antenna
mounting tab will be facing away from you) of the sup-
plied bracket, using the four holes provided for that pur-
pose located at each of the four corners of the bracket.
• Place the bracket on a solid surface. Grasping the edges
of the PCB, keeping the board face up, orient the four
holes on the PCB with the four standoffs protruding from
the bracket. Push the PCB firmly and evenly onto the
standoffs until the PCB is secured to the bracket.
• Remove the antenna cable, white whip antenna, brass
washer, nylon washer with bushing (thick flat washer),
nylon washer (flat), and brass nut from their bag.
• Connect the supplied 12.7cm (5") antenna cable to the radio by inserting the connector through to the Communicator board from
the back of the bracket, and then pushing the connector firmly into the socket on the radio.
• Place the nylon washer with bushing (thick flat washer) onto the threaded section of the cable. Insert the threaded section up
through antenna mounting tab. Place the second nylon washer (flat), followed by the brass washer and the brass nut, onto the
threaded section of the cable. Tighten the assembly by hand.
NOTE: Ensure the SIM card is inserted on the communicator.
2. Install the Communicator module into the Cabinet.
NOTE: Before installing the TL260GS/GS2060 or inserting/removing the SIM card,
ensure that the system is turned off.
• Remove the cabinet's front cover.
• Remove the circular knockout located in the top-right section of the cabinet. This
knockout will be used for connection of the supplied antenna.
• Attach the 4-pin PC-Link cable connector to the panel board.
NOTE: Note that the red wire is on the right and the black wire is on the left, whereas
on the Communicator this is reversed.
• Insert the Communicator into the panel cabinet.
• Locate the screw hole in the right hand wall of the panel. Line up the bracket and
the side wall and, using the screw provided, affix the two together (i). Ensure that
the threaded antenna connection point appears through the knockout hole of the
cabinet.
• There are four terminals on the Communicator available for power connection,
labeled PWR PWR GND GND.
• Attach either one of the two PWR terminals to the panel's BELL+ terminal.
• Attach the other PWR terminal to the positive of the Bell; also, attach the panel's
BELL- terminal to the negative of the Bell.
• Attach the Communicator's GND terminal to the panel's AUX- terminal.
• Locate the 2-terminal block labeled GND SHLD. The SHLD terminal must be wired to the cabinet's protective earth ground (EGND).
• In the cabinet, locate the plug for the Ethernet cable and affix.
• Reassemble the PC1864 cabinet.
• Attach the supplied antenna onto the antenna connector at the top right-hand side of the cabinet. Care must be taken not to over-
tighten the antenna, as damage to the antenna may occur as a result.
• Ensure the SIM card is inserted on the communicator.
NOTE: The installation procedure for the GS2060 is identical to the above, with the exception that it does not have the Ethernet option.
3. Turn on the panel and check signal strength.
• Power up the unit.
• The red and yellow LEDs will flash together while the communicator is initializing. The red and yellow LED will continue to flash until
the unit has successfully communicated to all programmed receivers. This operation may take several minutes to complete. Do not
leave the installation until the red and yellow LEDs have stopped flashing and there are no troubles indicated by the communicator.
• The green LEDs on the Communicator board will indicate the signal strength. The right-hand green LED must be on and solid - not
flashing - for the location to be acceptable. Please refer to Status LEDs on page 7 for more information.
Brass Washer
Nylon washer (flat)
Nylon Washer
with brushing
(thicker flat washer)
Mounting Holes
4
Brass nut
Antenna
Mounting Tab
Antenna
Mounting
Cable
Holes
PC-Link Cable Connector
(i)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Tl265gsGs2060Gs2065

Tabla de contenido