Connection With Aerocool Cooling Unit; Maintenance Instructions - Solter aeroprocess 4110 DV Manual De Instrucciones

CONNECTION WITH AEROCOOL COOLING UNIT

CONNECTION WITH AEROCOOL COOLING UNIT

MAINTENANCE INSTRUCTIONS

MAINTENANCE INSTRUCTIONS
Regular monitoring of the machine is recommended. Before performing any maintenance, disconnect the machine Regular monitoring of the machine is recommended. Before performing any maintenance, disconnect Regular monitoring of the machine is recommended. Before performing any maintenance, disconnect
from the mains. Reduce the recommended maintenance intervals in situations of intensive use. from the mains. Reduce the recommended maintenance intervals in situations of intensive use. from the mains. Reduce the recommended maintenance intervals in situations of intensive use.
INTERVAL
Weekly
Quarterly
Annual
FAULTS
In the event of any fault that may be hazardous to people, the machine and/or the environment, you must disconnect In the event of any fault that may be hazardous to people, the machine and/or the environment, you must disconnect In the event of any fault that may be hazardous to people, the machine and/or the environment, you must disconnect
the machine immediately and make sure it cannot be the machine immediately and make sure it cannot be reconnected until the problem that caused the fault has been
solved. Faults should only be eliminated by qualified personnel, taking into account the safety instructions of the solved. Faults should only be eliminated by qualified personnel, taking into account the safety instructions of the solved. Faults should only be eliminated by qualified personnel, taking into account the safety instructions of the
machine.
LISTADO DE POSIBLES AVERÍAS
ANOMALY
The machine doesn't start up
Anomaly indicator lights up
Overtemperature indicator lights up
The planned operation of the cooling unit is fully automatic. The power unit will detect the The planned operation of the cooling unit is fully automatic.
cooling unit without any adjustment. Connect the cooling unit to the remote connector at cooling unit without any adjustment. Connect the cooling
the base of the power unit. It may be necessary to remove the the base of the power unit. It may be necessary to remove the the base of the power unit. It may be necessary to remove the
protective cover. Please, make sure that once the cooling unit and power unit are protective cover. Please, make sure that once the cooling unit and power unit are protective cover. Please, make sure that once the cooling unit and power unit are
interconnected, the connection is well secured to avoid false contacts of the interconnected, the connection is well secured to avoid false contacts of the interconnected, the connection is well secured to avoid false contacts of the
interconnecting cable. During the first use, you may need to check the priming of the nterconnecting cable. During the first use, you may need to check the priming of the nterconnecting cable. During the first use, you may need to check the priming of the
coolant in the circuit. The machine will try to do it automatically. Alarm message 10 may coolant in the circuit. The machine will try to do it automatically. Alarm message 10 may coolant in the circuit. The machine will try to do it automatically. Alarm message 10 may
appear during the process. For more information on the operating modes of the cooling appear during the process. For more information on the operating modes of the coo appear during the process. For more information on the operating modes of the coo
unit, please, see the description of advanced setting parameter P.36 in this manual and/or unit, please, see the description of advanced setting parameter P.36 in this manual and/or unit, please, see the description of advanced setting parameter P.36 in this manual and/or
the Aerocool cooling unit manual. the Aerocool cooling unit manual.
Check the condition of wiring and external accessories. Check the condition of wiring and external accessories. Check the condition of wiring and external accessories.
Blow out the feed guide of the torch with compressed air and replace Blow out the feed guide of the torch with compressed air and replace worn Blow out the feed guide of the torch with compressed air and replace
components. components.
Clean and tighten the electrical connections of the welding circuit Clean and tighten the electrical connections of the welding circuit Clean and tighten the electrical connections of the welding circuit
Clean the drive unit with compressed air. Clean the drive unit with compressed air.
Remove all rollers from the drive unit, clean to remove dust and dirt and Remove all rollers from the drive unit, clean to remove dust and dirt and Remove all rollers from the drive unit, clean to remove dust and dirt and
lubricate slightly. lubricate slightly.
Carry out a complete inspection as specified by the standard EN Carry out a complete inspection as specified by the standard EN-60974.
See your dealer. See your dealer.
POSSIBLE CAUSE
Verify the mains.
Defective main switch.
Turn off the machine or unplug it from the mains for 1 minute and try Turn off the machine or unplug it from the mains for 1 minute and try
to start it up again.
Electronic circuit is defective.
Turn off the equipment for a minute and start it up again. If the error Turn off the equipment for a minute and start it u
persists, contact technical service.
The machine has become overheated. Wait until the machine The machine has become overheated. Wait until the machine
ACTION
reconnected until the problem that caused the fault has been
The power unit will detect the
unit to the remote connector at
40