Storing The Camera Settings In Memory - Presetting Feature; Setting The Speed Of The Camera Moving To A Preset Position - Sony RM-IP10 Manual De Instrucciones

Ocultar thumbs Ver también para RM-IP10:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Storing the Camera
Settings in Memory
– Presetting Feature
Up to sixteen combinations of settings (sixteen
positions), including camera position, zooming,
focusing, and backlighting, can be stored in the memory
of the camera using this unit.
RESET
JOYSTICK
VALUE
LOCK
POSITION
KNOB
RESET
+
R
PRESET
MODE
BRIGHT
1
SHIFT
9
+
GROUP
B
SELECT
AUTO
FOCUS
AUTO
1
POWER
MANUAL
ONE PUSH
NEAR
FAR
AF
1
Press the PAN-TILT RESET button to reset the pan/
tilt position.
2
Select the camera whose settings you want to
preset.
For camera selection, see "To select the camera that
you want to operate" (page 8).
3
Adjust the position, zooming, focusing and
backlighting of the camera.
4
While holding down the PRESET button (for
POSITION 1 to 8) or the SHIFT and PRESET
buttons (for POSITION 9 to 16), press the GROUP/
POSITION button in which you want to store the
settings.
While holding down (for POSITION 1 to 8)
POSITION
RESET
PRESET
1
SHIFT
9
While holding down (for POSITION 9 to 16)
The settings are stored in the memory of the
camera.
The pressed button flashes during storing. Flashing
stops when storing is completed.
To recall the stored settings
Press the GROUP/POSITION button in which you have
stored the settings.
14
GB
Storing the Camera Settings in Memory – Presetting Feature
4 1
BLACK
PAN-TILT
ONE PUSH
GROUP
MENU
LIGHT
RESET
AWB
GROUP
POSITION
2
3
4
5
6
7
8
10
11
12
13
14
15
16
CAMERA
2
3
4
5
6
7
2
Press a GROUP/POSITION button.
2
3
4
5
6
7
10
11
12
13
14
15
For POSITION 9 to 16, hold down the SHIFT button
then press the GROUP/POSITION button.
To cancel the preset memory
While holding down the RESET button (for POSITION
1 to 8) or the SHIFT and RESET buttons (for
POSITION 9 to 16), press the GROUP/POSITION
button from which you want to cancel the settings.
While holding down (for POSITION 1 to 8)
POSITION
RESET
PRESET
SHIFT
While holding down (for POSITION 9 to 16)
The pressed button flashes during canceling of the
settings. Flashing stops when the settings have been
canceled.
Notes
• When the power is turned on, the camera starts with
the settings stored in POSITION 1.
• If you want to retain the previous pan and tilt positions
when the power is turned off and turned on again, store
those positions in POSITION 1.
• When you are storing or canceling the settings in one
POSITION, you cannot call up, store or cancel the
settings in another POSITION.
Setting the speed of the camera
moving to a preset position
You can select the panning/tilting speed when the
camera moves to a preset position.
1
Select the camera whose speed you want to set.
For camera selection, see "To select the camera that
you want to operate" (page 8).
2
Press the GROUP/POSITION button for which you
8
16
want to set the speed for more than one second.
All the CAMERA buttons, 1 to 7, flash.
Press a GROUP/POSITION button.
1
2
3
4
5
6
7
9
10
11
12
13
14
15
8
16

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Brbk-ip10Brbk-ip7z

Tabla de contenido