Location And Function Of Parts; Ip Remote Controller Rm-Ip10; Ip Control Card Brbk-Ip10 (For Brc-H900/Z330); Ip Control Card Brbk-Ip7Z (For Brc-Z700) - Sony RM-IP10 Manual De Instrucciones

Ocultar thumbs Ver también para RM-IP10:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Location and Function
of Parts

IP remote controller RM-IP10

For details about the location and function of parts, refer
to the operating instructions of RM-IP10.
IP control card BRBK-IP10
(for BRC-H900/Z330)
1
BRBK-IP10
LAN
A LAN connector (RJ-45 8-pin)
Connect to a switching HUB that is compatible
with 10BASE-T/100BASE-TX using a LAN cable
(category 5 or higher, straight).
When a link is established, the green indicator
lights, and it flashes during communication. While
connected with 100BASE-TX, the yellow indicator
also lights.
Note
When the IP control card BRBK-IP10 is inserted
into the camera, the RS-232C and RS-422
connectors cannot be used.
B Reset switch
If you press down this switch with a pointed tip for
about five seconds, the camera will reboot and the
IP control card BRBK-IP10 will return to the
factory setting.
Factory settings for BRBK-IP10
• IP address: 192.168.0.100
• Subnet mask: 255.255.255.0
• Name: CAM1
C SDI 1, 2 connector (BNC type)
Outputs down-converted SD-SDI signals that
conform to SMPTE 259M serial digital interface
standards, or HD-SDI signals that conform to
SMPTE 292 serial digital interface standards.
When the menu display for the camera is turned
ON, you can use the 4 HD/SD select switch to
output the menu display signal that overlaps the
images, from this connector.
4
GB

Location and Function of Parts

2
3
4
1
2
DATA MIX
OFF
ON
HD
SD
SDI OUT
D HD/SD select switch
Switches between SD-SDI signals and HD-SDI
signals.
When outputting HD-SDI signals, you can select
whether to overlap the menu display with the image
output from SDI connectors 1 and 2.
• "HD/DATA MIX: ON" Outputs HD-SDI signal
and the menu display is overlapped.
• "HD/DATA MIX: OFF" Outputs HD-SDI signal
and the menu display is not overlapped.
• "SD": Outputs SD-SDI signal and the menu
display is overlapped.
Notes
• SD-SDI and HD-SDI signals cannot be supplied
simultaneously.
• Set the HD/SD select switch before turning on the
camera.
• Do not push the switch forcibly with a
screwdriver, etc.
IP control card BRBK-IP7Z
(for BRC-Z700)
1
2
1
BRBK-IP7Z
LAN
A LAN connector (RJ-45 8-pin)
Connect to a switching HUB that is compatible
with 10BASE-T/100BASE-TX using a LAN cable
(category 5 or higher, straight).
When a link is established, the green indicator
lights, and it flashes during communication. While
connected with 100BASE-TX, the yellow indicator
also lights.
Note
When the IP control card BRBK-IP7Z is inserted
into the camera, the RS-232C and RS-422
connectors cannot be used.
B Reset switch
If you press down this switch with a pointed tip for
about five seconds, the camera will reboot and the
IP control card BRBK-IP7Z will return to the
factory setting.
Factory settings for BRBK-IP7Z
• IP address: 192.168.0.100
• Subnet mask: 255.255.255.0
• Name: CAM1
3
4
2
HD
SD
SDI OUT

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Brbk-ip10Brbk-ip7z

Tabla de contenido