Publicidad
Idiomas disponibles
Idiomas disponibles
Counter-clockwise rotation – set the switch (5) to the extreme
right position.
* In certain cases position of the switch related to rotation may be different
than specified. Please refer to graphic signs located on the switch or tool
body.
Safe position of the direction selector switch (5) is in the middle,
it prevents accidental starting of the power tool.
• Drill cannot be started, when the switch is in this position.
• Use this position of the switch to change drills or bits.
• Before starting the tool make sure the position of the direction
selector switch (5) is correct.
Do not change direction of rotation when the drill spindle
is rotating.
CHANGE OF GEAR
Gear switch (4) (fig. H) allows to increase the range of rotational
speed.
Gear I: small speed range, big torque
Gear II: greater speed range, small torque.
Set the gear switch in position appropriate for the works to
perform. When the switch is blocked and cannot be moved, turn
the spindle slightly.
Never change the gear switch position when the drill is
operating. It may damage the power tool.
Long lasting drilling at low rotational speed of the spindle
may cause motor overheating. Long lasting drilling at
low rotational speed of the spindle may cause motor
overheating.
HOLDER
The drill provides convenient holder (6) that allows to e.g. hang
the tool on a tool belt when working at heights.
OPERATION AND MAINTENANCE
Remove the battery from the device before commencing
any activities related to installation, adjustment, repair or
maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the tool with a dry cloth or blow through with
compressed air at low pressure.
• Do not use any cleaning agents or solvents, they may damage
plastic parts.
• Clean ventilation holes in the motor casing regularly to
prevent device overheating.
• In case of excessive commutator sparking, have the technical
condition of carbon brushes of the motor checked by a
qualified person.
• Always store the tool in a dry place, beyond reach of children.
• Store the device with the battery removed.
QUICK RELEASE CHUCK REPLACEMENT
Quick-release chuck is screwed onto spindle of the drill and
additionally secured with a screw.
• Set the direction selector switch (5) in the middle position.
• Open jaws of quick release chuck (1) and unscrew the fixing
screw (left-hand thread) (fig. H).
• Install hexagonal key in the quick release chuck and tap the
other end of the key.
• Unscrew the quick release chuck.
• Installation of the quick release chuck is similar to
deinstallation, only the sequence of actions is reversed.
All defects should be repaired by service workshop authorized
by the manufacturer.
TECHNICAL PARAMETERS
RATED PARAMETERS
Cordless drill
Parameter
Battery voltage
Range of idle rotational speed
Range of quick release chuck
Torque control range
Max. torque (soft drive)
Max. torque (hard drive)
Protection class
Weight
Year of production
Graphite Energy+ System Battery
Parameter
Battery
Battery voltage
Battery type
Battery capacity
Ambient temperature range
Charging time for charger 58G002
Weight
Year of production
Graphite Energy+ System Charger
Parameter
Charger type
Supply voltage
Power supply frequency
Charging voltage
Max. charging current
Ambient temperature range
Charging time of the battery 58G001
Charging time of the battery 58G004
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Noise and vibration information
Parameters of produced noise level, such as sound pressure level
Lp
and sound power level Lw
A
are specified below in this manual, in compliance with EN 60745.
Vibration values a
and measurement uncertainty K are
h
determined in accordance with EN 60745-2-1 and specified
below.
14
Value
18 V DC
gear I
0-350 min
-1
-1
gear II
0-1250 min
2 -13 mm
1 – 19 +
drilling
35 Nm
55 Nm
III
1,3 kg
2017
Value
58G001
58G004
18 V DC
18 V DC
Li-Ion
Li-Ion
2000 mAh
4000 mAh
4
0
C – 40
0
C
4
0
C – 40
0
C
1 h
2 h
0,400 kg
0,650 kg
2017
2017
Value
58G002
230 V AC
50 Hz
22 V DC
2300 mA
4
0
C – 40
0
C
1 h
2 h
II
0,300 kg
2017
with measurement uncertainty K
A
Publicidad
