Descargar Imprimir esta página

Publicidad

Enlaces rápidos

Serta
Smart Layers™
®
Big and Tall Executive Chair
Silla ejecutiva de durabilidad
commercial marca Serta
Smart Layers™
Assembly Instructions
Instrucciones de ensamblaje
MODEL / MODELO
44950
45375
45376
®
Soporte m
á
ximo
de la silla:
181 kg
400 lbs
400 lbs

Publicidad

loading

Resumen de contenidos para Serta Smart Layers

  • Página 1 Serta Smart Layers™ ® Big and Tall Executive Chair Silla ejecutiva de durabilidad commercial marca Serta ® Smart Layers™ Assembly Instructions Instrucciones de ensamblaje MODEL / MODELO 44950 45375 45376 Soporte m á ximo de la silla: 181 kg 400 lbs...
  • Página 2: Instrucciones De Ensamblaje

    Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood floors.
  • Página 3: Arm Inserts Molduras Del Brazo

    PARTS/PARTES Seat Plate Casters Star Base Gas Lift with Telescoping Cover Ruedas Base en forma de estrella Mecanismo del asiento télescopique Quantity/cantidad: 5 Quantity/cantidad: 1 Elevador neumático y cubierta Quantity/cantidad:1 telescópica Quantity/cantidad: 1 Back Cushion Right Arm Seat Cushion Left Arm Cojín del respaldo Cojín del asiento Brazo izquierdo...
  • Página 4 Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Paso 1 Ponga la base en forma de estrella (B) con las patas hacia arriba e inserte las 5 ruedas (A) en los hoyos situados en la base (B). Step 2 Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover (C) through the center hole on top of Star Base (B).
  • Página 5 Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 2-1/2” Screws (J) for the front holes of the Seat Plate (D) and 7/8”...
  • Página 6 Step 4 Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever receivers on the underside of Seat Cushion (F). Push down the key on the receivers to pull out the levers. *Note : Fix the cable for the seat plate into the plastic clips attached to the bottom of the seat cushion.
  • Página 7 Step 5 Align the Back Cushion (G) with the Seat Cushion (F) by positioning the back support plate over the Seat Plate (D) with 1-1/4” Screws (K). *Note : Do not tighten the screws completely. Paso 5 Alinee el cojín del respaldo (G) con el cojín del asiento (F) por medio de colocar la placa de soporte del respaldo sobre la placa del asiento (D) con tornillos de 32mm (K).
  • Página 8 Step 6 Insert 1-1/2” Screws (L) into arm holes, attaching Arms (E1 & E2) to sides of Seat Cushion (F) and Back Cushion (G). *Note : Tighten all the screws completely. Remember to tighten the back support plate screws. Paso 6 Inserte los tornillos de 38mm (L) en los hoyos de los brazos y fije los brazos (E1 y E2) a los lados del cojín del asiento (F) y el cojín del respaldo (G).
  • Página 9 Step 7 Put the Plastic Shroud (H) over the Seat Plate (D) (with front of plastic shroud facing the front of seat cushion). Align shroud posts to holes on bottom of Seat Cushion (F) and press into position. Paso 7 Coloque la cubierta de plástico (H) sobre la plancha del asiento (D) (con la parte frontal de la cubierta de plástico mirando hacia el frente del...
  • Página 10 Step 8 Position the assembled chair upright with the seat plate facing down. Insert the Gas Lift with Telescoping Cover (C) into the center hole of the Seat Plate (D). Paso 8 Coloque la silla ensamblada verticalmente, con la plancha del asiento hacia abajo.
  • Página 11: Function Instruction

    Operating Instructions Mode d’emploi Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height : While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height.
  • Página 12 Function Instruction - 2 To Operate Tilt Lockout : While seated, reach under the left side of the chair to find the lever. Push down the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the up position.
  • Página 13 Function Instruction - 3 To Adjust Tension On The Tilt : Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user.
  • Página 14 Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt.
  • Página 15: Garantía Limitada

    Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así...

Este manual también es adecuado para:

449504537545376