Manuales relacionados para Serta COMERCIAL 45031
Resumen de contenidos para Serta COMERCIAL 45031
- Página 1 Serta Commercial Series-300 Executive Chair Serta Commercial Series-300 Executive Chair Assembly Instructions Instrucciones de ensamblaje MODEL / MODELO 45031 Soporte m á ximo de la silla: 136 kg 300 lbs 300 lbs...
-
Página 2: Instrucciones De Ensamblaje
Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood floors. - Página 3 PARTS/PARTES Casters Star Base Gas Lift with Telescoping Cover Seat Plate Ruedas Mecanismo del asiento Base en forma de estrella Elevador neumático y cubierta Quantity/cantidad: 5 telescópica Quantity/cantidad: 1 Quantity/cantidad:1 Quantity/cantidad: 1 Arms Seat Cushion Back Cushion Rear Plastic Shroud Brazos Cojín del asiento Cojín del respaldo...
- Página 4 Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Paso 1 Ponga la base en forma de estrella (B) con las patas hacia arriba y inserte las 5 ruedas (A) en los hoyos situados en la base (B). Step 2 Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover (C) through the center hole on top of Star Base (B).
- Página 5 Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-3/4” Screws (K) for the front holes of the Seat Plate (D) and 1”...
- Página 6 Step 4 Align the Back Cushion (G) with the Seat Cushion (F) and attach the back support plate onto the bottom of the Seat Cushion (F) by using 1-1/4” Screws (L). *Note : Do not tighten the screws completely. Paso 4 Alinee el cojín del respaldo (G) con el cojín del asiento (F);...
- Página 7 Step 5 Insert 3-1/4” Screws (M) into arm holes, attaching Arms (E) (with the front of arms facing the front of seat cushion) to sides of Seat Cushion (F) and Back Cushion (G). *Note : Tighten all the screws completely. Remember to tighten the back support plate screws.
- Página 8 Step 6 Put the Rear Plastic Shroud (H1) over the Seat Plate (D). Align shroud posts to holes on bottom of Seat Cushion (F) and press into position. Paso 6 Coloque la cubierta de plástico trasera (H1) en la placa del asiento (D). Alinee los postes de la cubierta con los huecos en la parte inferior del cojín del asiento (F) y presiónelos hasta dejarlos en posición.
- Página 9 Step 7 Put the Front Plastic Shroud (H2) over the Seat Plate (D) (with front of plastic shroud facing the front of seat cushion). Align shroud posts to holes on bottom of Seat Cushion (F) and press into position. Then join the Front Plastic Shroud (H2) and Rear Plastic Shroud (H1) together by easy snap locking the two ends.
- Página 10 Step 8 Insert Handles (I1 & I2) to the Seat Plate (D) as shown. Paso 8 Inserte las palancas (I1 y I2) en la placa del asiento (D) como se muestra en la imagen.
- Página 11 Step 9 Position the assembled chair upright with the seat plate facing down. Insert the Gas Lift with Telescoping Cover (C) into the center hole of the Seat Plate (D). Paso 9 Coloque la silla ensamblada verticalmente, con la plancha del asiento hacia abajo.
- Página 12 Step 10 Place the Plastic Caps (N) into arm holes once screws have been tightened. Paso 10 Ponga las tapas plásticas (N) en los hoyos de los brazos una vez que haya ajustado los tornillos.
-
Página 13: Function Instruction
Operating Instructions Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height : While seated, lean forward and reach under the right side of the chair to find the handle. Lift the handle and raise your body up slightly to allow the chair to rise to the desired height. To lower the seat, lift the handle while applying more weight downward on the seat. - Página 14 Function Instruction - 2 To Operate Tilt Lockout : Reach under the left side of the chair to find the handle. Flip the handle up and lean back to allow the chair to tilt backwards. Flip the handle down to lock the chair angle while the desired position is reached.
- Página 15 Function Instruction - 3 To Adjust Tension On The Tilt : Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user.
- Página 16 Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt.
-
Página 17: Garantía Limitada
Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así...