THOMSON ROC550 Manual De Instrucciones página 5

ROC 550 GB 18/07/02 10:36
Method C – Programming by means of code retrieval
Should none of the codes work, you still have the possibility of retrieving the appropriate
code without having to perform any input.
1. Switch on the set you want to control.
2. Hold down the S (6) key until the key that corresponds to the last mode you selected
blinks 3 times and then remains lit.
3. Press the key (15) that corresponds to the type of equipment you want to control:
TV: television set, VCR: video recorder, SAT: satellite receiver,
DVD: DVD player, AUX: other set
4. Direct the remote control towards the set and try to switch it off by pressing the
key B B (17).
5. If the set you want to control switches off, press OK (2) to memorise the subcode.
6. Should the set not switch off, press key B
times), until the set switches off. Between two key presses, leave enough time for the
key corresponding to the selected mode enough time to light up again (about 1
second). Proceeding this way will enable you to see whether the set responds or not.
7. Immediately upon the switching-off of the set to be controlled, press OK (2) to store
the code.
Note:
When programming the AUX key or if you want to assign another type of set than those
mentioned on the remote control, for example a satellite code in VCR mode, begin by
entering a code that corresponds to the set you want to programme (a 3-digit code that
you will find in the code booklet, see method B). Then begin the automatic search
(method D).
Example: if you want to control a satellite receiver with the AUX key, begin by entering
a satellite code (any satellite code that you find in the code list, for example: 603 for a
Thomson satellite receiver) then begin the automatic search procedure. The remote
control will then test all the satellite codes for the selected make.
Check of the programming:
In principle, your set is ready for receiving the remote control commands.
Check your remote control for proper functioning by performing the test described on
page 4:
Try out other remote control keys to find out the range of functions you can control.
If you think that not all of the keys are active, repeat the procedure of this
programming method to find out the code supporting a wider range of features.
With this method, the remote control scrolls through the full code list by sending an IR
signal to the set to be controlled remotely. Proceed as follows:
1. Check that your equipment is on. If not, switch it on manually.
2. Hold down the S (6) key until the key that corresponds to the last mode you selected
blinks 3 times and then remains lit (the indicator light remains on for a few seconds
to give you the time to proceed with the following steps. The indicator lamp flashes
to signal that this time is almost up, and then goes off).
3. Release the S key.
4. Press the key corresponding to the type of equipment (for example TV).
5. Press the PR + or standby B
the remote control begins to scroll through the whole code list included in the library
(at a rate of roughly 1 code per second).
Press the PR + key once again to slow down the test speed (1 code every 3 seconds).
As soon as the set changes channels, you must press OK (2) to save the code and
stop the remote control scrolling through the list. If you do not react quickly enough,
you can go back to the previous code by pressing PR - (4) or REW (G) as many
times as necessary (you can go forward by pressing B
if you have gone back too far). As soon as the set responds again, press OK (2) to
save the code.
Note:
When programming the AUX key or if you want to assign another type of set than those
mentioned on the remote control, for example a satellite code in VCR , mode, begin by
entering a code that corresponds to the set you want to programme (a 3-digit code that
you will find in the code booklet, see method B). Then begin the automatic search
(method D).
Example: if you want to control a satellite receiver with the AUX key, begin by entering
a satellite code (any satellite code that you find in the code list, for example: 603 for a
Thomson satellite receiver) then begin the automatic search procedure. The remote
control will then test all the satellite codes for the selected make.
Page 3
B (17) as many times as required (up to 200
Method D - Automatic code search
B (17) or PLAY (B -VCR only) key. After a few seconds,
B (17), PR + (4) or PLAY (B)
3
or or