Flex CS 60 WET Instrucciones De Funcionamiento Originales página 17

CS 60 WET/CSW 4161
Safety instructions
t^okfkd>
oÉ~Ç=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåëK=c~áäìêÉ=íç=çÄëÉêîÉ=íÜÉ=ë~ÑÉíó=
áåëíêìÅíáçåë=~åÇ=çíÜÉê=áåëíêìÅíáçåë=ã~ó=êÉëìäí=
áå ~å=ÉäÉÅíêáÅ=ëÜçÅâI=ÑáêÉ=~åÇLçê=ëÉêáçìë=áåàìêáÉëK=
hÉÉé=~ää=ë~ÑÉíó=áåëíêìÅíáçåë=~åÇ=çíÜÉê=
áåëíêìÅíáçåë=áå=~=ë~ÑÉ=éä~ÅÉ=Ñçê=íÜÉ=ÑìíìêÉK
 Always use the guard hood supplied with
the electric power tool. The guard hood
must be attached securely to the electric
power tool and adjusted to ensure maxi-
mum safety, i.e. the operator is exposed
to the smallest possible part of the inser-
tion tool. Ensure that you and anybody
in the vicinity remain outside the plane
of the rotating insertion tool.
The guard hood is intended to protect
the operator from fragments and accidental
contact with the insertion tool.
 Use only diamond-tipped cutting-off
wheels which were designed and recom-
mended by the manufacturer especially
for this electric power tool.
Just because you can attach the accessory
to your electric power tool does not guaran-
tee safe use.
 The permitted speed of the cutting-off
wheel must be at least as high as the
maximum speed indicated on the electric
power tool.
An accessory which rotates faster than
permitted may shatter and fly off.
 Cutting-off wheels may be used for
the recommended applications only.
For example: Never grind with the side
area of a diamond-tipped cutting-off
wheel.
Diamond-tipped cutting-off wheels
are designed for peripheral grinding.
If a lateral force is applied to these tools,
they may shatter.
 Always use undamaged clamping flanges
in the correct size and shape for the inser-
tion tool you have selected.
Suitable flanges support the insertion tools
and therefore reduce the risk of a break.
 Do not use worn cutting-off wheels from
larger electric power tools.
Insertion tools for larger electric power tools
are not designed for the higher speeds of
smaller electric power tools and may break.
 Outer diameter and thickness of the inser-
tion tool must correspond to the dimen-
sions of the electric power tool.
Incorrectly measured insertion tools cannot
be adequately shielded or controlled.
 The bores of the cutting-off wheels and
clamping flanges must exactly match
the grinding spindle of your electric
power tool.
Insertion tools, which do not fit exactly
on the grinding spindle of the electric
power tool, rotate unevenly, vibrate
violently and may result in loss of control.
 Do not use any damaged insertion tools.
Before use, always check the insertion
tools for splinters and cracks.
If the electric power tool or the insertion
tool is dropped, check for damage
or use an undamaged insertion tool.
When you have checked and inserted
the tool, ensure that you and anybody
in the vicinity remain outside the plane
of the rotating insertion tool and leave
the power tool running for one minute
at maximum speed.
Damaged insertion tools usually break
during this test time.
 Wear personal protective equipment.
Depending on the application, wear
full face protection, eye protection
or goggles. If appropriate, wear a dust
mask, hearing protection, protective
gloves and/or a special apron which
protect you from small sanding and
material particles.
You should protect your eyes from foreign
objects which are ejected for different appli-
cations. Dust and respirator masks must
filter the dust which is generated by the
power tool for the particular application.
If you are exposed to loud noise for a pro-
longed period, you may suffer hearing loss.
17