Flex CS 60 WET Instrucciones De Funcionamiento Originales página 25

CS 60 WET/CSW 4161
Parallel stop
t^okfkd>
_ÉÑçêÉ=éÉêÑçêãáåÖ=~åó=ïçêâ=çå=íÜÉ=ÉäÉÅíêáÅ=
éçïÉê=íççäI=éìää=çìí=íÜÉ=ã~áåë=éäìÖK
klqb
_ÉÑçêÉ=íÜÉ=ë~ï=Å~å=ÄÉ=éä~ÅÉÇ=áå=íÜÉ=ëìééäáÉÇ=
íê~åëéçêí~íáçå=Å~ëÉI=íÜÉ=é~ê~ääÉä=ëíçé=ãìëí=
ÄÉ êÉãçîÉÇK
To ensure optimum cutting results, the parallel
stop must be attached when sawing.
Stop edge upwards  Increases the contact
surface of the saw bench.
Stop edge downwards  Facilitates cutting
parallel to the workpiece edge.
Attaching parallel stop:
 Loosen wing screws (1.).
 Insert parallel stop (stop edge up or down)
and set to required width (2.).
 Retighten wing screws (3.).
Working with the power tool
`^rqflk>
Ó tÜÉå=íÜÉ=éçïÉê=íççä=áë=ëïáíÅÜÉÇ=çÑÑI=
íÜÉ Çá~ãçåÇJíáééÉÇ=ÅìííáåÖJçÑÑ=ïÜÉÉä=
ÅçåíáåìÉë=êìååáåÖ=ÄêáÉÑäóK
Ó tÜÉå=íÜÉ=êìååáåÖ=ÅìííáåÖJçÑÑ=ïÜÉÉä=
íçìÅÜÉë=íÜÉ=ïçêâéáÉÅÉI=~=âáÅâÄ~Åâ=
ã~ó çÅÅìêK
klqb
bñÅÉëëáîÉ=ÑÉÉÇ=äçïÉêë=íÜÉ=éÉêÑçêã~åÅÉ=
çÑ=íÜÉ=éçïÉê=íççäI=áãé~áêë=íÜÉ=ÅìííáåÖ=èì~äáíó=
~åÇ=êÉÇìÅÉë=íÜÉ=ëÉêîáÅÉ=äáÑÉ=çÑ=íÜÉ=Çá~ãçåÇJ
íáééÉÇ=ÅìííáåÖJçÑÑ=ïÜÉÉäK=
 Set cutting depth to the required
dimension.
 If required, set the mitre angle
(CS 60 WET only).
 Connect machine to the power supply.
 Take hold of the handle with your right
hand and the additional hand grip with
your left hand.
 Switch on saw and wait until the cutting-off
wheel has reached the maximum speed.
 Turn on water supply.
 Place saw bench on the workpiece without
bringing the diamond-tipped cutting-off
wheel into contact with the workpiece.
25