SKIL MASTERS F0157120 Serie Manual Original página 7

APPLICATION ADVICE
• When the foampad of the delta-tip is worn or damaged at
the top, you may extend its service life twice by turning it
120° (also applicable to delta sanding sheet) 7
• Never use the same sanding sheet for wood and metal
• Recommended sanding sheet grits:
coarse - for removing paint; for sanding of
extremely rough wood
medium - for sanding of rough or plain wood
fine - for smoothing of wood; for finishing of
bare wood; for smoothing surfaces with
old paint
• Use different grit sizes when the working surface is rough:
- start sanding with coarse or medium grit
- finish with fine grit
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially ventilation
slots F 2)
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in manufacturing
and testing procedures, repair should be carried out by an
after-sales service centre for SKIL power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60745, EN 61000,
EN 55014, in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
02.02.2011
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 82 dB(A) and the sound
power level 93 dB(A) (standard deviation: 3 dB),
and the vibration 5.3 m/s² (hand-arm method;
uncertainty K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintainted accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Ponceuse delta
INTRODUCTION
• Cet outil sert au ponçage et au polissage à sec du bois,
des surfaces peintes, du plastique, métal et mastic; il se
prête notamment à l'usinage des bords et des endroits
étroits et d'accès difficile
• Lisez et conservez ce manuel d'instruction 3
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Réservoir à poussière
B Adaptateur de l'aspirateur
C Bouton de retrait du réservoir à poussière
D Interrupteur marche/arrêt
E Molette de réglage de la vitesse de ponçage
F Fentes de ventilation
G Rangement pour la clé
H Coussinet de mousse supplémentaire
SECURITE
INSTRUCTIONS GENERALES DE SECURITE
ATTENTION! Lisez tous les avertissements de
sécurité et toutes les instructions. Ne pas suivre les
avertissements et instructions peut entraîner un choc
électrique, un incendie et/ou de graves blessures sur les
personnes. Conservez tous les avertissements et toutes
les instructions pour pouvoir s'y reporter
ultérieurement. La notion d'"outil électroportatif" dans les
avertissements se rapporte à des outils électriques raccordés
au secteur (avec câble de raccordement) et à des outils
électriques à batterie (sans câble de raccordement).
7
7120