Tabla de contenido
Publicidad
/ Feuille d'implémentation / Gráfica de implementación MIDI
*0
By default (factory settings) the PSR-330 ordinarily functions as a
16 channel multi-timbral tone generator. The Remote Channel can
be designated with the panel settings. The designated channel can
be controlled in the same manner as the PSR-330's keyboard ON/
OFF control. The following messages can be received by the
designated channel in this mode. All other messages will be
ignored.
• Note ON
• Note OFF
• Control change : Bank select MSB, LSB
Volume
Pan
Sustain
Reverb depth
All sound off
Reset all controller
• Program change
• Exclusive
*1
BANK SELECT
• The bank select MSB is used for melody and rhythm voice
switching.
(MSB 00H: Melody Voice/MSB 7FH: Rhythm Voice)
• Refer to the Voice List for details on LSB.
*2
RPN transmission/reception
Pitch bend Sensitivity
Fine Tune
Course Tune
Null
*3
Pitch Bend, modulation, expression, sustain, sostenuto and RPN
are returned to their default values. Also, resets the portamento
control.
*4
EXCLUSIVE
<GM System ON> F0H, 7EH, 7FH, 09H, 01H, F7H
• All parameters except MIDI Master Tuning settings are reset to
their default values.
<DISK ORCHESTRA ON> F0H, 43H, 73H, 01H, 14H, F7H
<DISK ORCHESTRA OFF> F0H, 43H, 73H, 01H, 13H, F7H
<MIDI MASTER VOLUME> F0H, 7FH, 7FH, 04H, 01H, ll, mm, F7H
• Allows the volume of all channels to be changed simulta-
neously. (Universal System Exclusive)
• "mm" is used as the MIDI Master Volume value ("ll" is ignored).
• The relationship between the MIDI Master Volume value and
the real volume is the same as the Control Change Master
Volume.
• The default value for "mm" is 7FH.
<MIDI MASTER TUNING>
F0H, 43H, 1nH, 27H, 30H, 00H, 00H, mm, ll, cc, F7H
• Simultaneously changes the tuning of all channels.
• "mm, ll" is used as the MIDI Master Tuning Value. The tuning
value is represented as follows:
T=M-128 (28<=M<=228)
T: Tuning Value (in cents)
M: is decimal value represented by 1-byte using bits 0..3 of
"mm" as the MSB and bits 0..3 of "ll" as the LSB.
• The default values for "mm" and "ll" are 08H, 00H. Also, n and
cc are recognized.
• This value is not reset by a GM System ON or Reset All
Controllers message.
BnH, 64H, 00H, 65, 00H
BnH, 64H, 01H, 65, 00H
BnH, 64H, 02H, 65, 00H
BnH, 64H, 7FH, 65, 00H
<BULK DUMP>
Resist Memory
F0H, 43H, 73H, 4CH, 06H, 09H, 0nH, 0nH, 0nH, 0nH, [DATA],
sum, F7H
0nH, 0nH, 0nH, 0nH : Data length (nnnnH Byte)
sum
User Song Data
F0H, 43H, 73H, 4CH, 06H, 0AH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH,
[DATA], sum, F7H
0nH, 0nH, 0nH, 0nH, 0nH, 0nH : Data length (nnnnnnH Byte)
sum
<Section Control> F0H, 43H, 7EH, 00H, ss, dd, F7H
• This message is related to the SW section operation.
ss : 00H-07H
08H
09H-0FH
10H
11H-17H
18H
19H-1FH
20H-27H
dd : Switch ON/OFF
<START, STOP Control> F0H, 43H, 6nH, xx, F7H
• This message controls the Start/Stop for the Style. (received
only)
n : Ignores the Device Number.
xx : 7A= Reset Start, 7D= Stop & Rewind
<TEMPO CONTROL> F0H, 43H, 7EH, 01H, tt, tt, tt, tt, F7H
• This message is used to change the Tempo Value.
tt, tt, tt, tt : Tempo Data
<Internal Clock, External Clock> (Received Only)
F0H, 43H, 73H, 01H, 02H, F7H (Internal Clock)
F0H, 43H, 73H, 01H, 03H, F7H (External Clock)
• This message controls the Clock Mode of the Style.
<XG System ON> (Received Only)
F0H, 43H, 1nH, 4CH, 00H, 00H, 7EH, 00H, F7H
n : ignores the Device Number.
• All parameters except MIDI Master Tuning are reset to their
default values.
• Remote Channel setting is canceled.
• This message requires approximately 50ms to execute, so
sufficient time should be allowed before the next message is
sent.
<XG Parameter Change>
F0H, 43H, 1nH, 4CH, aaH, bbH, ccH, ddH, ..., F7H
n:
Device number is ignored.
aa, bb, cc: address High, Mid, Low
dd:
data (successive transmission and reception are
possible within the amount of data shown in the
following Table-1)
• For more details refer to Table-1.
Caution: The PSR-330 corresponds to the XG parameters in
Table-1, but this is only a portion of XG parameters.
The PSR-330 does not completely correspond to the
XG format.
*5
It is possible to switch between the External and Internal Clocks.
*6
Start/Stop commands for the style can only be received when
External Clock is ON.
*7
All MIDI messages will be ignored when in the Song Mode.
: Check Sum
: Check Sum
INTRO
MAIN A
MAIN B
FILL IN AA
FILL IN BB
FILL IN AB
FILL IN BA
ENDING
7FH (ON)/ 00H (OFF)
87
Publicidad
Tabla de contenido
