Assembly And Adjustments - DeWalt DWH201D Traducido De Las Instrucciones Originales

• Risk of squeezing fingers when changing the accessory.
• Health hazards caused by breathing dust developed when
working in concrete and/or masonry.
Package Contents
The package contains:
1 Dust extraction connection port
1 Side handle assembly
1 Depth adjustment rod
1 Long bellow
1 Short bellow
1 Short adapter
1 Medium adapter
1 Long adapter
1 Dust port plug
1 Wear ring
1 Dust hose
1 Ring adapter for SDS plus® rotary hammers
1 Ring adapter for percussion hammer drills
1 Instruction manual
• Check for damage to the tool, parts or accessories which may
have occurred during transport.
• Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Dust Extraction System
The following pictograms are shown on the tool:
Read instruction manual before use.
Description

WARNING: Never modify the dust extraction system or
any part of it. Damage or personal injury could result.
Side Handle
1
Ring opening
2
Ring adapter
3
Wear ring
4
Long bellow
5
Intended Use
The DWH201D dust extraction system has been designed for
the extraction of dust when hammerdrilling into masonry or
concrete, and with solid drill bits mounted to the power tool.
This dust extraction attachment will fit most D
cordless SDS plus® rotary hammers, corded percussion hammer
drills and premium cordless drill/driver/hammerdrills. For
more information about D WALT power tools compatible with
e
this attachment, please contact your local dealer, refer to the
addresses at the back of the manual or visit www.dewalt.com.
DO nOt use under wet conditions or in the presence of
flammable liquids or gases.
The dust extraction system is an attachment for use with
professional power tools.
Depth adjustment rod
6
Dust extraction connection
7
port
Dust hose
8
WALT corded and
e
DO nOt let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start‑up
can cause injury.
Attaching the Ring Adapter (Fig. A, B)
Your dust extraction system comes with two adaptors; a toothed
adaptor for SDS plus® rotary hammers
adaptor for percussion hammerdrills
If the diameter of the tool's collar
adaptor is needed to properly mount the dust extraction system.
nOtE: If the diameter of the tool's collar is 54 mm, no ring
adapter is needed. Refer to the Technical Data in your tool's
manual for the proper collar diameter.
1. If a ring adapter is needed, choose the correct ring adaptor
for your tool.
2. Open the ring adaptor and slide it onto the tool's collar
with the lip of the adapter facing forward as shown in
Figure B.
nOtE: The adaptor will slide back and forth on the tool.
Assembling the Dust Extraction System
(Fig. A, C–E)
1. Choose the correct tool holder adapter for your tool (Fig. D).
‑ Short adapter is for use with standard SDS plus®
tool holders.
Medium adapter is for use with Quick Change Chuck
‑
(QCC) SDS plus® tool holders
‑ Long adapter is for use with the DCH417, D25413,
and D25417.
2. Assemble the long 25 , medium
holder adapter to the dust extraction connection port
using the supplied screw and a cross head screwdriver (Fig.
C). Tighten securely.
3. Carefully slide the newly assembled dust extraction
connection port and ring adapter into the slot on the right
hand side of the side handle assembly
click (Fig. E).
EngLIsh
15 and a smooth
16 .
18 is 43 mm or 48 mm, a ring
18
13 , or short 14 tool
7
9 until you hear a
13