Operation - Kärcher B 60 W Bp Manual Del Usuario

Operation

DANGER
Risk of injury. Push the pedal for raising/
lowering the cleaning head with one foot
only. The other foot must firmly be placed
on the floor.
In dangerous situations, release the safety
switch/drive lever.
Driving
ATTENTION
Risk of damage. The suction bar must be
lifted for reversing.
Note:
The device is designed and built in such a
way that the cleaning head protrudes to-
wards the right. This enables working in a
comfortable way close to the edges.
 Plug in the Intelligent Key.
 Preselect the speed on the drive speed
rotary knob.
 Turn the programme selection switch to
transport mode.
 Drive the machine.
Forwards:
Press the driving lever to the front.
Backward:
Press the driving lever to the rear.
Note:
The device moves only when the driving le-
ver is moved by 15°.
 Stop the machine: Release driving lever.
Filling in detergents
Fresh water
 Open the lock of the fresh water reser-
voir.
 Fill fresh water (maximum 60 °C) until
the lower edge of the filling nozzle.
 Close the lock of the fresh water reser-
voir.
With automatic fill of fresh water reser-
voir (option)
 Connect the hose to the automatic fill-
ing system and open the water supply
(max. 60 °C, max. 5 bars).
 Monitor the appliance - the automatic
filling system will interrupt the water
supply when the tank is full.
 Shut off the water supply and discon-
nect the hose from the appliance.
Detergent
WARNING
Risk of damage. Only use the recommend-
ed detergents. With other detergents, the
operator bears the increased risk regarding
the operational safety and danger of acci-
dent.
Only use detergents that are free from sol-
vents, hydrochloric acid and hydrofluoric
acid.
Follow the safety instructions for using de-
tergents.
Note:
Do not use highly foaming detergents.
Recommended detergents:
Application
Routine cleaning of all water
resistant floors
Routine cleaning of glossy
surfaces (e.g. granite)
Routine cleaning and basic
cleaning of industrial floors
Routine cleaning and basic
cleaning of fine stoneware tiles
Routine cleaning of tiles in
sanitary areas
Cleaning and disinfection in
sanitary areas
Removal of coating from all al-
kali-resistant floors (e.g. PVC)
Removal of coating from li-
noleum floors
Appliance with dosing equipment DOSE
(option)
Detergent is added to the fresh water on
the way to the cleaning head with the help
of a dosaging device.
Note:
The dosing unit can be used to add 3% de-
tergent at maximum. With higher dosage
the detergent must be put into the fresh wa-
ter tank.
 Place the detergent bottle into the holder.
 Close the bottle lid.
 Insert the suction hose of the dosaging
equipment into the bottle.
Note:
If the fresh water tank is empty, then the
function of adding detergent gets deactivat-
ed. The cleaning head continues to work
without the addition of any liquid.
Models without dosing equipment
 Add the detergent to the fresh water
reservoir.
Setting the water quantity
 Adjust the water quantity using the reg-
ulating button according to the dirt on
the floor covering.
Note:
Carry out initial cleaning attempts with low
water volume. Increase water volume step-
by-step until the desired cleaning result is
achieved.
The detergent pump of the dosing equip-
ment does not start working until a mini-
mum water volume is present.
Setting the Vacuum Bar
Oblique position
To improve the vacuuming result on tiled
floors the vacuum bar can be turned to an
oblique position of up to 5°.
 Loosen the wing nuts.
 Turn the vacuum bar.
4
-
EN
Detergent
RM 746
RM 780
RM 755 es
RM 69 ASF
RM 753
RM 751  Tighten the wing screws.
Inclination
RM 732
If the vacuum result is unsatisfactory the in-
clination of the straight vacuum bar can be
modified.
RM 752
 Adjust the rotary handle to incline the
suction bar.
RM 754
Setting the parameters
With yellow Intelligent Key
Parameters for the different cleaning pro-
grammes are preset in the appliance.
Depending on the authorisation of the yel-
low Intelligent Key, individual parameters
can be changed.
If you wish to permanently change the pa-
rameters, you must use a grey Intelligent
Key. This adjustment procedure is de-
scribed in the section "Grey Intelligent
Key".
Note:
Almost all displayed text regarding param-
eter adjustment is self-explanatory. The
only exception is the parameter FACT:
– Fine Clean: Lower brush speed for re-
moving the grey film on fine stone
floors.
– Whisper Clean: Medium brush speed
for regular cleaning with reduced noise
level.
– Power Clean: High brush speed for pol-
ishing, crystallising and sweeping.
 Turn the program selection switch to
the desired cleaning program.
 Turn the info button until the desired pa-
rameter is displayed.
 Press Info button - the set value blinks.
 Set the desired value by turning the info
button.
 Confirm the changed setting by press-
ing the Info button or wait till the set val-
ue is automatically accepted after 10
seconds.
ATTENTION
Risk of damage to the floor covering. Do
not operate the appliance on the spot.
 Turn the program selection switch to
the desired cleaning program.
Lower the cleaning head
 Press the pedal for lowering the clean-
ing head downwards slightly and then
move it to the left. This unlocks the ped-
al. Release the pedal slowly upwards.
The cleaning head is lowered.
Note:
The brush motor comes to a halt when the
machine stops and when there is overload.
Cleaning
17