Kärcher IVC 60/24-2 Tact2 Lp Manual Del Usuario página 8

Please read and comply with these origi-
nal instructions prior to the initial opera-
tion of your appliance and store them for
later use or subsequent owners.
– Before first start-up it is definitely necessary to read
the safety indications Nr. 5.956-249.0!
– The non-compliance of the operating and safety in-
structions may lead to damages of the appliance
and to dangers for the operator and other persons.
– In case of transport damage inform vendor immedi-
ately.
Environmental protection
Danger or hazard levels
Proper use
Device elements
Start up
Operation
Transport
Storage
Care and maintenance
Troubleshooting
Warranty
Accessories and Spare Parts
EU Declaration of Conformity
Declaration of Conformity (UK)
Technical specifications
Environmental protection
The packaging material can be recycled.
Please do not throw the packaging mate-
rial into household waste; please send it
for recycling.
Old appliances contain valuable materi-
als that can be recycled; these should be
sent for recycling. Batteries, oil, and sim-
ilar substances must not enter the envi-
ronment. Please dispose of your old ap-
pliances using appropriate collection sys-
tems.
Notes about the ingredients (REACH)
You will find current information about the ingredients
at:
www.kaercher.com/REACH
Danger or hazard levels
DANGER
Pointer to immediate danger, which leads to severe in-
juries or death.
WARNING
Pointer to a possibly dangerous situation, which can
lead to severe injuries or death.
CAUTION
Pointer to a possibly dangerous situation, which can
lead to minor injuries.
ATTENTION
Pointer to a possibly dangerous situation, which can
lead to property damage.
8
Contents
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
WARNING
The appliance is not suitable for vacuuming dust which
endangers health.
– This disposal system is intended for the low-dust
disposal of dry or slightly moist vacuumed material
while using a waste hose that can be cut to length.
– This appliance is suited for commercial and indus-
trial use, e.g. in storage and assembly areas and
on production machines.
– The appliance is not approved for crane loading.
Device elements
1
1 Power cord
1
2 Nameplate
1
3 Filter dedusting
1
4 Flat fold filter
1
5 Suction head
1
6 Handle of the suction head
2 7 Left unlocking of the placement mechanics
8 Tin tub
2
9 Disposal system
2
10 Sheathed cable
2
11 Right unlocking of the placement mechanics
3
12 Handle of the disposal system
3
13 Suction head lock
3
14 Waste hose
4
15 Steering roller of the chassis with parking brake
4 16 Floor nozzle holder
17 Chassis
18 Drain pan
19 Suction support
20 Holder for suction pipe
21 Intermediate ring
22 Rotating knob
23 Filter cover
24 Cable clamp
25 Push handle
 Bring the appliance to working position - secure it,
if required, with parking brakes.
 Insert the suction hose (not included) into the suc-
tion hose connection.
 Ensure that the disposal system has been inserted
properly.
 Attach the desired accessories (not included).
Inserting the waste hose
 Remove all 4 loops of the waste hose (length:
22 m).
Illustration
 Open the intake by a rotation to the left and pull it
out towards the bottom.
 Insert the waste hose as shown in the illustration.
 Insert the intake and lock it by clockwise rotation.
Illustration
 Pull down the waste hose 40-50 cm.
 Close the end of the waste hose by means of a ca-
ble tie.
ATTENTION
The flat pleated filter must always be in place while vac-
uuming.
– 1
EN
Proper use
Start up
Operation