Maxi-Cosi Titan Pro Manual Del Usuario página 31

EN
• Recommend adjust to full recline position before ISOFIX system installation. After well-install
ISOFIX connector and top tether, adjust to proper recline position for child.
• The Maxi-Cosi Titan Pro has been approved in accordance with the latest European safety stand-
ards (ECE R44/04) and is suitable for children from 9 to 36 kg.
• The Maxi-Cosi Titan Pro must be installed with ISOFIX and Top Tether when your child's weight
is form 9kg to 18 kg. You can use vehicle belt only, or vehicle belt and ISOGO, or vehicle belt and
ISOGO and Top Tether to install the Titan Pro car seat when you child's weight is 15-36 kg.
• Make sure the fold-down rear seat is locked into position.
• Make sure that any luggage and other objects liable to cause injuries in the event of a collision
shall be properly secure.
• Make sure the straps holding the carseat to the vehicle are tight.
WARNING:
When the car seat is installed on the front passenger seat, we recommand to switch off the front
passenger airbag if your child is sitting in a front-facing position and place the passenger seat in
the rearmost position.
Baby in the Titan Pro car seat :
• Never leave your child unattended.
• For your own safety and the one of your child always put the child in the car seat and fasten him
however short your journey may be.
• Use the Maxi-Cosi Titan Pro only on a front-facing seat that is fitted with an automatic or static
3-point belt that has been approved according to the ECE R16 standard or similar. Do NOT use a
2-point belt.
• After putting the child in the car seat, ensure that the harness is sufficiently tight by pulling the
belt. Before every use, make sure the harness is not damaged or twisted.
• Make sure you can fit no more than one finger between the harnesses and your child (1cm). If
58
there is more space than 1 cm, tighten the harness belt further.
• Check to make sure the headrest is adjusted to the proper height.
• Ensure that the straps under the stomach lie as low as possible, to properly support the pelvis.
• Do not use the child restraint device without the cover. Do not replace the seat cover with any
other than the one recommended by the manufacturer, because it will have a direct effect on the
functioning of the car seat.
• The temperature inside a vehicle may become very high, particularly after a long period of expo-
sure to the sun. It is strongly recommended, under such conditions, to cover the seat of the car
with a piece of material or something equivalent to prevent the harness fixings, and in particular
the metal parts, from becoming hot and burning the child.
ATTENTION:
In ISOFIX use the fitting clips for lower anchorage to the vehicle are not sufficient. It is essential to
fix the "TOP TETHER" to the upper anchorage point recommended by the car manufacturer. Fitting
the Titan Pro seat with additional tethers using the vehicle's ISOFIX additional anchorage points.
The ISOFIX anchors have been developed to obtain a safe and easy fixation of the child safety
systems inside the car. Not all cars are equipped with these anchors although they are standard on
more recent models. Consult the attached list of cars for which the car seat can be installed cor-
rectly (you can also consult additional updates of this list on the website www.maxi-cosi.com).
• In forward facing position, the seat must be placed on the car rear seat or exceptionally on the
front seat in accordance with the legislation in force in the country of use (In France: in accord-
ance with the conditions stipulated in decree n° 91-1321 du 27-12-1991).If you use the Titan
Pro on the front seat, it is recommented to deactivate the airbag of the seat in question and
move the passenger seat back to a maximum (Please consult your car manual).
• When installing the car seat, it is necessary to remove the headrest in order to put the TOP
TETHER through correctly.
Autogoods "130"
EN
59