JB Systems Light RADIANT LASER Manual De Instrucciones página 7

ENGLISH
000-127 128 different fixed positions along the Y axis
CH 8
128-191 Clockwise moving along the Y axis
Y AXIS MOVING
192-255 Anticlockwise moving along the Y axis
000-016 BLUE
CH 9
017-031 GREEN
COLOR
032-049 BLUE & GREEN
050-255 Changing colors
000 No grating rotation
CH 10
001-075 Clockwise grating rotation
GRATING
076-150 NO grating rotation
ROTATION
151-255 Anticlockwise grating rotation
10CH DMX-chart 10-C (DMX CHANNEL1 set between values 225 and 255)
CHANNEL VALUE
CH 2
000-255 11 different standard patterns
000-127 Fixed pattern size: from big (100%) to small (5%)
CH 3
128-169 Zooming in (from big to small + from slow to fast)
ZOOMING
170-209 Zooming out (from small to big + from slow to fast)
210-255 Zooming in & out (from slow to fast)
000-127 0° to 359° fixed positions around Y axis
CH 4
Y AXIS
128-191 Clockwise rolling around Y axis
ROLLING
192-255 Anticlockwise rolling around Y axis
000-127 0° to 359° fixed positions around X axis
CH 5
X AXIS
128-191 Clockwise rolling around X axis
ROLLING
192-255 Anticlockwise rolling around X axis
CH 6 000-127 0° to 359° fixed positions around Z axis
Z AXIS
128-191 Clockwise rolling around Z axis
ROLLING
192-255 Anticlockwise rolling around Z axis
000-127 128 different fixed positions along the X axis
CH 7
128-191 Clockwise moving along the X axis
X AXIS MOVING
192-255 Anticlockwise moving along the X axis
000-127 128 different fixed positions along the Y axis
CH 8
128-191 Clockwise moving along the Y axis
Y AXIS MOVING
192-255 Anticlockwise moving along the Y axis
000-016 Original colors
017-031 BLUE
CH 9
032-047 GREEN
COLOR
048-062 BLUE + GREEN (CYAN)
063-160 Changing between Blue and green (from slow to fast)
161-255 Changing mix of 3 colors (from slow to fast)
CH 10
NOT USED
JB SYSTEMS
®
USER MANUAL
DESCRIPTION
9/66 RADIANT LASER
ENGLISH
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
 Always dry the parts carefully.
 Clean the external optics at least once every 30 days.
 Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Input: AC 100~240V, 50/60Hz
Fuse: 250V 1A slow blow (20mm glass)
Total Power consumption: 30W
Sound Control: Internal microphone
DMX connections: 3pin XLR male / female
DMX channels: 1 or 10 channels
DMX starting address: 001  512
Laser Power: 40mW Green CW laser (λ = 532nm)
200mW Blue CW laser (λ = 450nm)
Laser radiation class: 3B
Beam diameter @ aperture: <5mm
Divergence (each beam) <2 mrad
Divergence (total output) <160°
Working temperature: 15°C to 40°C
Laser Safety Standard: EN/IEC 60825-1 Ed2, 2007-03
Size: see picture below
Weight: 2,6kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
JB SYSTEMS 10/66
®
USER MANUAL
RADIANT LASER