Standard Accessories; Prior To Operation - Hitachi Koki SV 12SG Instrucciones De Manejo

English
SPECIFICATIONS
Voltage (by areas)*
Power Input
No-load speed
Sanding pad size
Sanding paper size
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

○ Sanding paper ..............................................................1
○ Dust bag .......................................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
1. Sanding paper
○ 114 × 140 mm paper clip type sanding paper
Grain: AA60, AA100, AA150
○ 110 × 100 mm Velcro type sanding paper
Grain: AA60, AA100, AA150
○ 110 × 100 mm stick-on type sanding paper
Grain: AA60, AA80, AA100, AA120, AA150, AA180
○ Outer diameter 125 mm stick-on type sanding paper
Grain: AA60
2. Sanding pad
○ 110 × 100 mm sponge pad (Velcro type)
○ 110 × 100 mm stick-on pad
○ Outer diameter 125 mm stick-on pad
3. Punch plate
Optional accessories are subject to change without notice.
APPLICATIONS
○ Finish polishing of woodwork surfaces
○ Sanding surfaces of woodwork or sheet metal prior to
painting, etc.

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF positon. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operating
immediately, which could cause a serious accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Installing the sanding paper
(1) Bending the sanding paper:
Position the sander with its pad side facing upward as
shown in Fig. 1. Place the sanding paper on the pad so
that the center of the sanding paper is aligned with the
center of the pad, and bend both ends of the sanding
paper at a 90° angle. Then, bend both ends again in the
manner shown in Fig. 2. The sanding paper is now ready
to be installed on the sander.
3
(110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)
200 W*
14000/min
110 mm × 100 mm
114 mm × 140 mm
1.1 kg
(2) Installing the sanding paper:
While ensuring that the cord is not bent, place the sander
on a workbench as shown in Fig. 3, and insert one end
of the sanding paper (bent section). Next, insert the
remaining bent section in the same manner.
CAUTION
The sanding paper must be precisely installed on the
pad, ensuring that there is ample tension (leaving no
slack). Loosely installed sanding paper could result in
unevenly sanded surfaces and/or damage to the sanding
paper itself.
5. Attaching and Removing the Dust Bag
(1) Attaching the Dust Bag
As shown in Fig. 4, hold the dust gate and push it in the
direction of Arrow A to attach it to the dust outlet.
(2) Removing the Dust Bag
As shown in Fig. 4, hold the dust gate and pull it in the
direction of Arrow B to remove it from the dust outlet.
CAUTION
Prior to the sanding operation, make sure the material of
surface you are going to sand.
If the surface under sanding operation is expected to
generate harmful / toxic dusts such as lead painted
surface, make sure the dust bag or appropriate dust
extraction system is connected with dust outlet tightly.
Wear the dust mask additionally, if available.
Do not inhale or touch the harmful / toxic dusts generated
in sanding operation, the dust can endanger the health of
yourself and bystanders.
PRACTICAL OPERATING PROCEDURES
CAUTION
Never apply water or grinding fl uid when sanding. This
could result in electrical shock.
1. Switching the sander ON and OFF
The power can be turned on by setting the lever to ON (1)
and turned off by setting the lever to OFF (0).
CAUTION
Never turn the power switch ON when the sander is
contacting the surface to be sanded. This is necessary
to preclude damage to the material. The same applies
when switching the power OFF.
2. How to hold the orbital sander
While gripping the housing, lightly press the sander
against the surface to be sanded so that the sanding
paper uniformly contacts the surface, as shown in Fig.
5. DO NOT apply excessive pressure to the sander while
sanding. Excessive-pressure may cause overload of the
motor, reduced service life of the sanding paper, and
lowered sanding or polishing effi ciency.
3. How to move the orbital sander
For optimum operating effi ciency, alternately move the
sander forward and backward at a constant speed and
balance.