Maintenance; Maintenance Schedule - Husqvarna DE 110i Manual De Usuario

2. Close the air flow that moves through the air intake
with the air intake plug or the intake valve to make
vacuum. (Fig. 30)
3. Wait 5 seconds until vacuum is made, then push the
filter purge button. Do this step 3 to 5 times. It is
important to let the product make vacuum between
each button push. (Fig. 31)
If the suction is not sufficient after this procedure, it is
necessary to clean the prefilter with water. Refer to
clean the prefilter with water on page 21 .
To install a new Longopac bag cassette
CAUTION:
you install a new Longopac cassette. Refer
To clean the prefilter with water on page
to
21 .
1. Put the Longopac cassette around the inner edge of
the Longopac holder.
2. Remove the 4 straps after you put the Longopac in
the holder.
3. Pull the inner layer of the Longopac cassette up (A)
and fold it into the holder (B). (Fig. 32)
4. Attach the Longopac holder to the rear part of the
container (A). Then attach the Longopac holder to
the sides and to the front of the container (B). Push
the Longopac holder up until you hear a solid click.
(Fig. 33)
5. Make sure that the Longopac is sealed. (Fig. 34)
6. Pull the outer layer of the Longopac cassette down.
(Fig. 35)
7. Close the bottom of the Longopac with a cable tie.
(Fig. 36)
Introduction
WARNING:
safety chapter before you do maintenance
work on the product.
WARNING:
you do maintenance on the product.
WARNING:
correctly can decrease the product life
cycle and increase the risk of accidents.
1618 - 004 - 24.01.2022
To
Clean the prefilter before

Maintenance

Read and understand the
Remove the battery before
Failure to do maintenance
To discard a full Longopac bag and
prepare a new Longopac bag
WARNING:
caution, a full Longopac bag can be heavy.
Make sure that the cable ties are closed
correctly before you lift the Longopac bag.
1. Pull out the Longopac bag (A) and attach a cable tie
(B) to close the new Longopac bag. (Fig. 37)
2. Shake down the dust in the used Longopac bag.
3. Attach a cable tie 10 cm/3.9 in. below the first cable
tie to close the used Longopac bag. Cut off the
Longopac bag between the cable ties. (Fig. 38)
4. If the remaining part of the Longopac bag cassette
is too small to prepare a new Longopac bag, install
a new Longopac bag cassette. Refer to
new Longopac bag cassette on page 19 .
5. Obey local regulations for disposal of the full
Longopac bag.
To do after completed work
1. Do the filter purge procedure. Refer to
dust particles from the prefilter during operation on
page 18 .
2. Stop the product, refer to
18 .
3. Discard the Longopac bag. Refer to
Longopac bag and prepare a new Longopac bag on
page 19 .
4. Clean the product. Refer to
page 21 .
5. Prepare the product for transportation. Refer to
move the product long distances on page 25 .
All servicing and/or repair work must also
be done by a professional. Turn to your
servicing dealer for more information.
WARNING:
obey all local regulations to dispose the
dangerous dust correctly, before and during
maintenance.

Maintenance schedule

The maintenance intervals are calculated from daily use
of the product. The intervals change if the product is not
used daily.
Lift the Longopac bag with
To install a
To remove
To start and stop on page
To discard a full
To clean the product on
To
Make sure that you
19