Functional Description; Installing Or Removing Battery Cartridge - Makita PB002G Manual De Instrucciones

For preparation of the item being shipped, consult-
i n g a n e x p e r t f o r h a z a r d o u s m a t e r i a l i s r e q u i r e d .
Please also observe possibly more detailed
n a t i o n a l r e g u l a t i o n s .
Tape or mask o open contacts and pack up the
battery in such a manner that it cannot move
a r o u n d i n t h e p a c k a g i n g .
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
speci ed by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
s i v e h e a t , e x p l o s i o n , o r l e a k o f e l e c t r o l y t e .
1 3 . If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may cause heating, catching fire,
burst and malfunction of the tool or battery car-
tridge, resulting in burns or personal injury.
1 7 . Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near a high-voltage elec-
trical power lines. I t m a y r e s u l t i n a m a l f u n c t i o n
or breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
a l s o v o i d t h e M a k i t a w a r r a n t y f o r t h e M a k i t a t o o l a n d
c h a r g e r .
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3 . Charge the battery cartridge with room tem-
perature at 0 C - 40 C
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period more than six months .
0 F - 04 F . Let
7 ENGLISH

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is
switched o and the battery cartridge is removed
before adjusting or checking function on the tool.

Installing or removing battery cartridge

CAUTION:
Always switch o the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge rmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip o your hands
and result in damage to the tool and battery cartridge
and a personal injury.
Fig.1: 1. R e d i n d i c a t o r 2. B u t t o n 3. B a t t e r y c a r t r i d g e
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
i t i n t o p l a c e . I n s e r t i t a l l t h e w a y u n t i l i t l o c k s i n p l a c e
w i t h a l i t t l e c l i c k . I f y o u c a n s e e t h e r e d i n d i c a t o r a s
shown in the figure, it is not locked completely.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. I f n o t ,
it may accidentally fall out of the tool, causing injury to
y o u o r s o m e o n e a r o u n d y o u .
CAUTION:
Do not install the battery cartridge
forcibly. I f t h e c a r t r i d g e d o e s n o t s l i d e i n e a s i l y , i t i s
not being inserted correctly.
Indicating the remaining battery capacity
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
l i g h t u p f o r a f e w s e c o n d s .
Fig.2: 1. I n d i c a t o r l a m p s 2. Check button
Indicator lamps
Lighted O
Remaining
capacity
Blinking
7 5% t o 100%
50% t o 7 5%
25% t o 50%
0% t o 25%
C h a r g e t h e
battery.
The battery
m a y h a v e
m a l f u n c t i o n e d .