Parts Description - Makita UC002G Manual De Instrucciones

4 . If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5. Do not short the battery cartridge:
( 1 ) Do not touch the terminals with any con-
ductive material.
( 2 ) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to water
( 3 )
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6. Do not store and use the tool and battery car-
tridge in locations where the temperature may
reach or exceed 50 °C (122 °F).
7 . Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Do not nail, cut, crush, throw, drop the battery
cartridge, or hit against a hard object to the
battery cartridge. S u c h c o n d u c t m a y r e s u l t i n a
fire, excessive heat, or explosion.
9. Do not use a damaged battery.
10. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
F o r c o m m e r c i a l t r a n s p o r t s e . g . b y t h i r d p a r t i e s ,
f o r w a r d i n g a g e n t s , s p e c i a l r e q u i r e m e n t o n p a c k -
a g i n g a n d l a b e l i n g m u s t b e o b s e r v e d .
F o r p r e p a r a t i o n o f t h e i t e m
i n g a n e x p e r t f o r h a z a r d o u s m a t e r i a l i s r e q u i r e d .
P l e a s e a l s o o b s e r v e p o s s i b l y m o r e d e t a i l e d
n a t i o n a l r e g u l a t i o n s .
Tape or mask off open contacts and pack up the
b a t t e r y i n s u c h a m a n n e r t h a t i t c a n n o t m o v e
a r o u n d i n t h e p a c k a g i n g .
11. When disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specified by Makita. I n s t a l l i n g t h e b a t t e r i e s t o
non-compliant products may result in a fire, exces-
s i v e h e a t , e x p l o s i o n , o r l e a k o f e l e c t r o l y t e .

PARTS DESCRIPTION

► Fig.2
1 T o p h a n d l e
4 F r o n t h a n d g u a r d
7 C h a i n c a t c h e r
10 B a t t e r y c a r t r i d g e
13 C a p
16 F r o n t h a n d l e
19 G u i d e b a r c o v e r
b e i n g s h i p p e d , c o n s u l t -
2 Lock-off lever
5 G u i d e b a r
8 R e t a i n i n g n u t
11 M a i n p o w e r l a m p
14 Adjusting screw (for oil pump)
17 O i l t a n k c a p
-
13 ENGLISH
1 3 . If the tool is not used for a long period of time,
the battery must be removed from the tool.
1 4 . During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may cause heating, catching fire,
b u r s t a n d m a l f u n c t i o n o f t h e t o o l o r b a t t e r y c a r -
tridge, resulting in burns or personal injury.
1 7 . Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near a high-voltage elec-
trical power lines. I t m a y r e s u l t i n a m a l f u n c t i o n
o r b r e a k d o w n o f t h e t o o l o r b a t t e r y c a r t r i d g e .
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
U s e o f n o n - g e n u i n e M a k i t a b a t t e r i e s , o r b a t t e r i e s t h a t
h a v e b e e n a l t e r e d , m a y r e s u l t i n t h e b a t t e r y b u r s t i n g
causing fires, personal injury and damage. It will
a l s o v o i d t h e M a k i t a w a r r a n t y f o r t h e M a k i t a t o o l a n d
c h a r g e r .
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3 . Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4 . When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
3
6
9
12
15
18
- -
S w i t c h t r i g g e r
S a w c h a i n
Chain adjusting screw
M a i n p o w e r s w i t c h
C a r a b i n e r
S p i k e b u m p e r
-