Scheppach HF60 Traducción Del Manual De Instrucciones Original página 31

Parts for table width extension (Fig. 2)
• Left table width extension (1a)
• Right table width extension (1b)
• Table width extension mounting device (11)
• 8x Hexagonal socket screw M5 x 12 (l)
• 6x Hexagonal socket screw M5 x 20 (m)
• 14x Washer Ø 5 (n)
• 8x Nut M5 (o)
Installing the table width extensions (Fig. 3)
The table width extensions (1) enlarge the table sur-
face and thus enable the machining of large workpiec-
es and the execution of special milling operations.
• Table extensions (1a + 1b) on both sides with 4 Allen
screws M5 x 20 (l), 4 washers Ø 5 (n) and 4 hexagon
nuts M5 (o) on each side and with 3 Allen screws
M5 x 12 (l) and 3 washers Ø 5 (n) on the front of the
work table (3).
• Push the table width extension mounting device (11)
into the groove until it rests on the left table width
extension (1a) or the right table width extension (1b)
and the work table (4).
• Tighten the table width extension mounting device
(11).
• Tighten all screw connections firmly.
• Repeat the process on the other side.
Parts for cutter stop (Fig. 4)
• 2x Stop bar (2a)
• 2x Retaining device (2g)
• 2x Vertical stop support (2b)
• 2x Fastening clamp (2i)
• Pressure bar (2d)
• Pressure bar holder (2e)
• 2x Horizontal stop support (2h)
• Moving stop (2c)
• Stop base body (2f)
• Front pressure bar (9)
• Front pressure bar holder with screws (9a)
• Suction adapter (12)
• 2x Hexagonal socket screw M6 x 16 (g)
• 2x Hexagonal bolt M6 x 40 (c)
• 6x Coach bolt M6 x 20 (f)
• 2x Coach bolt M6 x 25 (d)
• 5x Coach bolt M6 x 35 (e)
• 2x Knurled screw M6 (a)
• 10x Knurled nut M6 (b)
• 2x Wing nut M6 (i)
• 15x Washer (h)
• 2x Nut M6 (j)
Installing the cutter stop (Fig. 5 - 16)
Step 1 (Fig. 5)
• Attach the 2 retaining devices (2g) to the horizontal
stop support (2h) using 2 carriage bolts M6 x 35 (e),
2 washers Ø 6 (h) and two knurled nuts M6 (b).
Step 2 (Fig. 6):
• Attach the pressure bar (2d) to the pressure bar
holder (2e) using 2 carriage bolts M6 x 25 (d), 2
washers Ø 6 (h) and 2 wing nuts M6 (i).
Step 3 (fig. 7):
• Insert the suction adapter (12) into the stop base
body (2f).
Step 4 (fig. 8):
• Fix the vertical stop supports (2b) to the stop base
body (2f) and to the movable stop (2c) using a hexa-
gon socket screw M6 x 16 (g) each.
Step 5 (fig. 9):
• Place the movable stop (2c) in the groove provided
in the stop base body (2f) and secure it using a car-
riage bolt M6 x 20 (f), washer Ø 6 (h) and knurled nut
M6 (b) and a carriage bolt M6 x 35 (e), washer Ø 6
(h) and knurled nut M6 (b).
• On the left side fit a carriage bolt M6 x 20 (f) with
washer Ø 6 (h) and counter-lock it with a knurled nut
M6 (b).
Step 6 (Fig. 10 + 11)
• Insert two hexagonal bolts M6 x 40 (c) from below
into the stop base body (2f) (Fig. 10).
• Fix the pressure bar holder (2e) to the pressure bar
(2d) using the two M6 x 40 hexagon bolts (c), two Ø
6 washers (h) and two M6 nuts (j). (fig. 11)
• To fasten the stop bars, fit four carriage bolts M6 x
20 (f), four washers Ø 6 (h) and four knurled nuts
M6 (b).
Step 7 (fig. 12):
• Attach the two support brackets horizontally (2h)
with the retaining devices (2g) to the vertical stop
supports (2b) using two fastening clamps (2i) and
two knurled screws M6 (a) as shown in fig. 12.
Step 8 (fig. 13+14):
• Slide the two stop bars (2a) with the carriage bolts
M6 x 20 (2f) as shown in fig. 13 and 14.
www.scheppach.com GB | 31