Bosch D-tect200C Instrucciones De Funcionamiento Y Seguridad página 20

Dtect200C_2610067510_06-21.qxp_D-tect200 6/14/21 9:30 AM Page 20
Open the file browser on your PC and select the
BOSCH D‑tect 200 C drive. The saved files can
be copied from the internal memory of the
detection tool, moved to your PC or deleted.
As soon as you have completed the required
operation, disconnect the drive following the
standard procedure.
Note: Always disconnect the drive from the
operating system of the PC first (eject drive), as
failure to do so may damage the internal memory
of the detection tool.
Then switch off the detection tool using the
on/off button (8). Remove the USB Type-C®
cable (21). Close the flap for the USB Type-C®
port (4) to protect it from dust or splashes.
Note: Use the USB Type-C® interface to connect
the detection tool to a PC only. The detection
tool may be damaged if connected to other
devices.
Note: The USB Type-C® interface can only be
used for data transfer. Rechargeable batteries or
other devices cannot be charged by this
interface.
Data Transfer via SD Card
If an SD card is inserted in the detection tool,
images are automatically stored on the card
when saved, not in the internal memory of the
detection tool.
To insert the SD card, open the flap of the slot
(3). Pay attention to the correct orientation
when inserting the SD card. Close the flap of the
slot (3) to protect it from dust or splashes.
Note: Switch off the detection tool before
removing the SD card. Otherwise, the SD card
may be damaged.
Main Menu
To access the main menu, press the left-hand
function button (15).
Navigating in the menu
– To scroll through a menu: Press the up (17) or
down (12) arrow buttons.
– To switch to a submenu: Press the red start
button (16) or the right-hand arrow button (7).
– To confirm a selected menu option: Press the
red start button (16).
– To change a menu option using the on/off
switch: press either the red start button (16),
Operating Instructions
the left-hand (14) or the right-hand arrow
button (7). This will also save the menu
option.
– To go back to the next highest menu: Press the
left-hand function button (15) under the Back
arrow.
– To leave the main menu and go back to
measuring: Press the right-hand function
button (6) under the Home symbol.
Menu options
– <Measuring mode>
Set
"Overview of the measuring modes", page 15).
Once you have made your selection, the
detection tool will directly switch to the selected
measuring mode.
In the <Object Detection> measuring mode, you
can also set the wall type suitable for the
planned measurement and the view for the
measurements.
– <Device settings> ▪ <Ruler>: Switch on/off the ruler for the
measuring modes <Object Detection> (with
the exception of the <Spot View>) and for
the <Leakage Detection>. Using the ruler,
you can determine the distance between
object centers, for example. Press the right-
hand function button (6) to set the ruler to
▪ <Depth zero.
indicator for the <Object depth> and the
maximum permissible <Drilling depth>.
▪ <Display brightness>: Set the brightness
▪ <Audio signals>: Switch the audio signal on level of the display backlight.
or off. When the audio signal is switched on,
an audio signal sounds every time a button
is pressed and every time an object is found
▪ <Start-up settings>: Choose the settings within the sensor range.
(e.g. wall type, view, ruler) that the
detection tool starts up when it is switched
on. Choose between applying the settings
from the last time the tool was switched off
and personalized basic settings (these are
▪ <Switch off after ...>: Choose the time the current settings in the main menu).
interval after which the detection tool will
switch off automatically if it is not in use.
-20-
the required measuring
mode>: Choose
mode (see
between the