Bosch PEX 220 A Instrucciones De Servicio página 8

Ocultar thumbs Ver también para PEX 220 A:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
Product Specifications
Eccentric Sander
Order number
Rated input power
No-load speed
Stroke rate at no load
Eccentricity
Sanding plate dia.
Weight without mains
cable approx.
Protection class
The specifications apply for the rated voltage of [U]
230/240 V. For lower voltages and with models for
specific countries, the specifications can vary.
Please observe the order number of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured values determined according to EN 50 144.
Typically, the A-weighted sound pressure level of the
product is 77 dB(A). The noise level when working can
exceed 85 dB(A).
Wear ear protection!
The typical hand-arm vibration is below 2.5 m/s
Product Elements
Please open the foldout page with the illustration of the
tool and leave it open while you read these operating
instructions.
The numbering of the machine elements refers to the
illustration of the machine on the graphic page.
1 On-Off switch
2 Dust box (micro-filtersystem)
3 Sanding plate
4 Sanding sheet*
5 Outlet piece
6 Latching lever
7 Filter element (micro-filtersystem)
8 Screws (accessory kit)*
9 L-type Torx key*
10 Extraction adapter*
* Not all the accessories illustrated or described are in-
cluded in standard delivery.
2 609 000 112 • (03.10) T
All manuals and user guides at all-guides.com
PEX 220 A
3 603 C78 0..
[W] 220
[RPM] 12000
[RPM] 24000
[mm] 2.5
[mm] 125
[kg] 1.1
/ II
2
.
English–1
Intended Use
The machine is intended for dry sanding of wood,
plastic, metal and filler material as well as painted sur-
faces.
Machines with electronic control are also suitable for
polishing.
For Your Safety
Working safely with this machine is
possible only when the operating
and safety information are read
completely and the instructions
contained therein are strictly fol-
lowed.
In addition, the general safety
notes in the enclosed booklet must
be observed.
If the cable is damaged or cut through while work-
s
ing, do not touch the cable but immediately pull the
mains plug. Never use the machine with a dam-
aged cable.
Connect machines that are used in the open via a
s
residual current device (RCD) with an actuating
current of 30 mA maximum. Do not operate the
machine in rain or moisture.
Wear safety glasses.
s
Safety gloves are recommended.
s
Always direct the cable to the rear away from the
s
machine.
Secure the workpiece. A workpiece clamped
s
with clamping devices or in a vice is held more se-
cure than by hand.
The machine can be used only for dry sanding.
s
Working with material containing asbestos is not
s
permitted.
Always hold the machine firmly when working and
s
provide for a secure stance.
When sanding metal, flying sparks are produced.
s
Take care that no persons are endangered. Be-
cause of the danger of fire, no combustible materi-
als should be located in the vicinity (spark flying
zone).
If your tool is equipped with a dust bag, empty it
s
frequently and after completion of sanding. Be
extremely careful of dust disposal, materials in fine
particle form may be explosive. Do not throw sand-
ing dust on an open fire. Spontaneous combustion
may in time, result from mixture of oil or water with
dust particles.
Always switch the machine off and wait until it has
s
come to a standstill before placing it down.
Never allow children to use the machine.
s
Bosch is able to ensure flawless functioning of the
s
machine only if the original accessories intended
for it are used.

Publicidad

Tabla de contenido
loading

Tabla de contenido