Denon AVR-1802 Instrucciones De Operación página 15

[2] Listening over headphones
1 Connect the headphones to the
PHONES
PHONES jack of the front panel.
2
Press the SPEAKER A or B
button turn the speaker off.
(Main unit)
CAUTIONS:
• No sound is produced from the headphones when
speakers A or B are turned on.
• When an external power amplifier is connected to
the front preout jacks, turn off the external power
amplifier's speaker switch.
[3] Turning the sound off temporarily (muting)
1 Use this to turn off the audio output
MUTING
temporarily.
Press the MUTING button.
Cancelling MUTING mode.
(Remote
Press the MUTING button again.
control unit)
Muting will also be cancelled
when MASTER VOL is adjusted
up or down.
[4] Combining the currently playing sound with the desired image
1 Simulcast playback
VIDEO SELECT
Use this switch to monitor a video
source other than the audio source.
Press the VIDEO SELECT button
repeatedly until the desired source
(Remote
control unit)
appears on the display.
Cancelling simulcast playback.
• Select "SOURCE" using the VIDEO SELECT
button.
• Switch the program source to the component
connected to the video input.
[5] Checking the currently playing program source, etc.
1
Front panel display
• Descriptions of the unit's operations
STATUS
are also displayed on the front panel
display. In addition, the display can
DISPLAY
be switched to check the unit's
operating status while playing a (Remote
control unit)
source by pressing the STATUS
button.
NOTE:
To prevent hearing loss, do not raise the volume level
excessively when using headphones.
B
1
2
SYSTEM SURROUND
SET UP MENU
MASTER
CH SELECT VOL
SELECT
T.TONE STATUS MUTING
1
RETURN DISPLAY
3 2 0
VIDEO SELECT CD·MD/CDR·DVD/VDP DISC SKIP+
1
TITLE
8 3 9
2
6 7
SET UP MENU MASTER
CH SELECT VOL
SELECT
T.TONE STATUS MUTING
1
RETURN DISPLAY
CHANNEL TV VOLUME
Playback using the external input (EXT. IN) jacks
1 Set the external input (EXT.
IN) mode.
8
Press the EXT. IN button to
switch the external input.
(Main unit)
(Remote
Once this is selected, the
control unit)
input signals connected to
the FL (front left), FR (front right), C (center), SL
(surround left) and SR (surround right) channels
of the EXT. IN jacks are output directly to the
front (left and right), center, surround (left and
right) speaker systems without passing through
the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SUBWOOFER jack.
2
Cancelling the external input mode
To cancel the external input (EXT. IN) setting,
press the INPUT MODE (AUTO, PCM, DTS) or
ANALOG button to switch to the desired input
mode. (See page 13,14.)
8
(Main unit) (Remote control unit)
• When the input mode is set to the external input
(EXT. IN), the play mode (STEREO, DOLBY/DTS
SURROUND, 5CH STEREO or DSP SIMULATION)
cannot be set.
Recording the program source (recording the source currently being monitored)
1
Follow step 1 to 3 under "Playing the input
source".(Page 13, 14.)
Simultaneous recording
The signals of the source selected with the function selector button are output simultaneously to the
CDR/TAPE and VCR AUDIO OUT jacks. If a total of 3 tape and/or video decks are connected and set to the
recording mode, the same source can be recorded simultaneously on every decks.
NOTES:
• The AUDIO IN's signal selected with the function selector button are output to the CDR/TAPE and VCR
AUDIO OUT jacks.
• The DIGITAL IN's signal selected with the function selector button are output to the DIGITAL OUT (OPTICAL)
jack.
B
2 1
V. AUX VCR-1 VCR-2 TV/DBS
4 5 6 7
INPUT MODE CDR / TAPE TUNER SHIFT
1, 2
8 9 0
SURROUND
TAPE · VCR
MODE
6 7
CHANNEL
NOTES:
• In play modes other than the external input mode,
the signals connected to these jacks cannot be
played. In addition, signals cannot be output from
channels not connected to the input jacks.
• The external input mode can be set for any input
source. To watch video while listening to sound,
select the input source to which the video signal
is connected, then set this mode.
2 Start recording on the tape or video deck.
For instructions, refer to the component's operating
instructions.
ENGLISH
15