Operating Instructions; Machine Assembly - GGP ITALY B 26 J Traducción Del Manual Original

8) Be careful during adjustment of the machine
to prevent entrapment of the fingers between the
cutting means and fixed parts of the machine.
9) Do not touch the cutting means until the spark
plug cable has been disconnected and the cut-
ting means is completely stationary. When serv-
icing the cutting means, bear in mind that, even
though the spark plug cable is disconnected, the
cutting means can still move.
10) Check the guard frequently for wear or dete-
rioration. Replace it if it is damaged.
11) Replace any instruction or warning message
stickers, if damaged.
12) Store the machine out of the reach of chil-
dren.
13) Do not store the machine with fuel in the tank
in an area where the fuel vapours could reach
an open flame, a spark or a strong heat source.
14) Allow the engine to cool down before storing
in any enclosure.
15) To reduce fire hazards, clean the machine
and especially the engine thoroughly to get rid
of any grass cuttings, leaves or excess grease,
never leave containers with the cut debris inside
the storage area.
16) If the fuel tank has to be emptied, this should
be done outdoors once the engine has cooled
down.
17) Before putting the machine away, check you
have removed wrenches or tools used for main-
tenance.
E) RESIDUAL RISKS
1) Even when all safety prescriptions are com-
plied with, there may be certain residual risks
that can not be excluded. Potential foreseeable
hazards depend on the type and construction of
the machine and can include:
– I njuries to fingers and hands if caught in the ro-
tation of the cutting means
– I njuries to feet if struck by the cutting means
– I njuries to eyes if protection goggles are not
worn (hurling of stones and soil)
– I njuries to hearing ability if no ear protection
devices are worn.
F) TRANSPORTATION AND HANDLING
1) Whenever the machine is to be handled or
transported you must:
– T urn off the engine, wait for the cutting means
to stop and disconnect the spark plug cap;
– F it the cutting means guard;
– O nly hold the machine using the handgrips
and position the cutting means in the opposite
direction to that used during operations.
2) When using a vehicle to transport the ma-
chine, position it so that it can cause no danger
All manuals and user guides at all-guides.com
to persons and fasten it firmly in place to avoid it
from tipping over, which may cause damage or
fuel spillage.
1) Environmental protection should be a priority
of considerable importance when using the ma-
chine, for the benefit of both social coexistence
and the environment in which we live. Try not to
cause any disturbance to the surrounding area.
2) Scrupulously comply with local regulations
and provisions for the disposal of packaging,
oils, petrol, filters, damaged parts or any ele-
ments which have a strong impact on the envi-
ronment; this waste must not be disposed of as
normal waste, it must be separated and taken to
specified waste disposal centres where the ma-
terial will be recycled.
3) Scrupulously comply with local regulations
for the disposal of waste materials after mowing.
4) At the time of decommissioning, do not pol-
lute the environment with the machine, hand it
over to a disposal centre, in accordance with the
local laws in force.
NOTE - The figures mentioned in the text
are found on page iii and following of this
manual.
IMPORTANT The machine is supplied with
some of the components disassembled and the
fuel tank empty.
tive gloves to handle the cutting devices.
Mount the components very carefully so as
not to impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
the assembly should be done on a flat and
stable surface, with enough space for moving
the machine and its packaging, always mak-
ing use of suitable equipment.
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.
1.1 COMPLETING THE MACHINE
1.1a. "MONO" models (Fig. 1)
– P osition the cap (1) inserting the pin (1a) in one
5
G) ENVIRONMENTAL PROTECTION

OPERATING INSTRUCTIONS

1. MACHINE ASSEMBLY

WARNING! Always wear strong protec-
WARNING! Unpacking and completing
of the three holes on the drive tube.