Sammic CK-24V Instrucciones página 16

EN
MAINTENANCE
- Verify before each use that the machine's safety devices are working prop-
erly. Call the SAMMIC authorised technical service if you detect any anomaly.
- Check the condition of the drive shaft seal on a weekly basis to ensure
that this area remains water-tight. Installation of a new seal is recommended
every time the drive shaft is loosened for maintenance.
- If the power cable is damaged, a new one must be installed before the
machine is used again. Only a SAMMIC authorised technical service may
perform this replacement.
- If the engine block (K) or any other part is damaged, the affected parts must
be replaced before the machine is used again. Only a SAMMIC authorised
technical service may perform this change.
- The noise level in operation (according to EN ISO 11201:1995) is less than
70 dB(A) with the machine placed at a height of 1.6 m and a distance of 1 m.
Background noise: 32 dB(A).
FUNCTIONS AND OPERATION OF THE ELECTRONIC
CONTROL
ON/OFF (14):
Starts the motor if all the safety devices permits it. Pressing a second time
stops the motor.
PRESS (15):
The motor starts and runs as long as this key is held down and stops when
it is released.
In Cutter mode.
- If the machine is in continuous operation, pushing PRESS (15) stops it and
deactivates the timer.
- If a programme is running and you push PRESS (15), the machine stops
and the timer returns to the initial point.
UP (11)
Each time the key is pressed the setting on the display increases.
DOWN (12)
Each time the key is pressed the setting on the display decreases.
TIMER (13)
Cutter mode:
Press to activate the countdown function. Use the UP (11) or DOWN (12)
buttons to adjust the time. After selecting the time, a second press confirms
the selection.
Veg. slicer mode:
Press and hold for three seconds to access the FORCE CONTROL function.
OPERATION
When the machine is switched on, the "Viewer" (1) displays two central
lines (wait). Icon number 7 (representing a cutting disk) is displayed on the
Viewer if the "Vegetable Cutter" accessory is mounted and Icon number 5
(representing a rotor) is displayed if the "Cutter" is mounted, Indicating that
the control plate has Identified each accessory. The speed level and the
associated RPM are also displayed.
Ten different speeds (1 to 10) and programmes P1, P2 and P3 can be
selected in "Cutter" mode and five different speeds (1 to 5) can be selected
in "Vegetable Cutter" mode.
- Time control: Only available in "Cutter" mode. The countdown time and
automatic shut-down can also be programmed.
- If the Start button is pushed when any of the safety devices is out of posi-
tion, an associated indicative text will appear on the screen.
START-UP AND GENERAL OPERATION
"Vegetable Cutter" operating mode (CK-24V, CA-2V)
The "Vegetable Cutter" accessory (F) can be positioned in two different
directions (FIG 3) so that the outlet for the products faces one direction or
the other.
With the machine disconnected from the mains:
- Place the "Vegetable Cutter" accessory on the motor block and turn it anti-
clockwise as shown in the drawings (Fig.4).
- The lid (E) must be fitted as shown in the drawings by turning it anticlock-
wise (Fig. 5)
- Place the plunger (B) as shown in the drawings and fasten it in position
with the pin (C). (Fig.6)
Installation of disks (A) and screens (G)
- Remove the lid (E) - plunger (B) assembly by turning it clockwise (Fig.5).
- Place the ejector (I) in its housing on the drive shaft or discharge ramp
(H).
- The screen (G) is inserted into the lid cavity (F) when required by the
process.
- Fit a disk (A) on the drive shaft. Disks that work with screens need to be
fastened in position.
- Reinsert the lid (E) - plunger (B) assembly by turning it anticlockwise
(Fig. 5).
Start the machine and the screen will display the Icon number 7 (represent-
ed by a cutting disk), the speed level ,and its associated RPM. The speed
can be adjusted with the motor running or stopped.
Pressing "Start" (7) with the lid (E) closed and the plunger (B) down will
start the motor. The Icon No. 7 will begin to rotate, indicating that the motor
is in movement.
The "Pause" icon will be displayed if "Start" (7) is pressed with the motor
stopped, the hinged lid (E) closed, and the plunger (B) up, indicating that
the plunger must be lowered. The motor will start when the plunger (B) is
lowered.
The running motor will stop if the plunger (B) is raised. When the plunger
(B) is lowered, the motor restarts automatically. The running motor will stop
if the hinged lid (E) is opened. When the hinged lid (E) is closed, it starts
up again.
If the plunger (B) is not lowered or the lid is not closed for more than 15
seconds, the "Start" button (7) must pressed again to start the motor .
If the machine Is left running with the plunger (B) in the lowered position,
the machine will stop automatically after 30 minutes.
If the Start (7) button is pushed when any of the safety devices is out of
position, an associated indicative text will appear on the screen.
The PRESS button (15) also works in cutter mode: the motor starts while it
is held down and stops when it is released.
- 16 -