ENG
The product shall not be used for purposes or in ways other than those for which the product is intended for and as described in this manual.
Incorrect uses can damage the product and cause injuries and damages.
The company shall not be deemed responsible for the non-compliance with a good manufacture technique of gates as well as for any de-
formation, which might occur during use.
Keep this manual for further use.
This manual has been especially written to be use by qualified fitters.
Installation must be carried out by qualified personnel (professional installer, according to EN 12635), in compliance with Good Practice
and current code.
Make sure that the structure of the gate is suitable for automation.
The installer must supply all information on the automatic, manual and emergency operation of the automatic system and supply the end
user with instructions for use.
Packaging must be kept out of reach of children, as it can be hazardous. For disposal, packaging must be divided the various types of waste
(e.g. carton board, polystyrene) in compliance with regulations in force.
Do not allow children to play with the fixed control devices of the product. Keep the remote controls out of reach of children.
This product is not to be used by persons (including children) with reduced physical, sensory or mental capacity, or who are unfamiliar with
such equipment, unless under the supervision of or following training by persons responsible for their safety.
Apply all safety devices (photocells, safety edges, etc.) required to keep the area free of impact, crushing, dragging and shearing hazard.
Bear in mind the standards and directives in force, Good Practice criteria, intended use, the installation environment, the operating logic of
the system and forces generated by the automated system.
Installation must be carried out using safety devices and controls that meet standards EN 12978 and EN 12453.
An omnipolar switch/section switch with remote contact opening equal to, or higher than 3mm must be provided on the power supply mains.
Make sure that before wiring an adequate differential switch and an overcurrent protection is provided.
Pursuant to safety regulations in force, some types of installation require that the gate connection be earthed.
During installation, maintenance and repair, cut off power supply before accessing to live parts.
Also disconnect buffer batteries, if any are connected.
The electrical installation and the operating logic must comply with the regulations in force.
The leads fed with different voltages must be physically separate, or they must be suitably insulated with additional insulation of at least 1 mm.
The leads must be secured with an additional fixture near the terminals.
During installation, maintenance and repair, interrupt the power supply before opening the lid to access the electrical parts
Check all the connections again before switching on the power.
The unused N.C. inputs must be bridged.
WASTE DISPOSAL
As indicated by the symbol shown, it is forbidden to dispose this product as normal urban waste as some parts might be harmful for environ-
ment and human health, if they are disposed of incorrectly.
Therefore, the device should be disposed in special collection platforms or given back to the reseller if a new and similar device is purchased.
An incorrect disposal of the device will result in fines applied to the user, as provided for by regulations in force.
Descriptions and figures in this manual are not binding. While leaving the essential characteristics of the product unchanged, the manufacturer reserves
the right to modify the same under the technical, design or commercial point of view without necessarily update this manual.
GENERAL INFORMATION
This automatic system, with 230Vac single-phase power supply for sliding
gates, is available in the following versions:
BULL 5M/OM
for gates with maximum weight equal to 500kg
BULL 8M/8OM
for gates with maximum weight equal to 800kg
BULL is a monobloc system featuring a refined design and reduced dimen-
sions. The motor and an irreversible reduction system, manufactured with
high resistant materials, are housed in an aluminium container. BULL is
equipped with spring limit switches. The customised key emergency release
allows to open and close the gate in case of power failure.
Anti-crash safety is ensured by an electronic device (encoder and ampero-
metric sensor) which detects any obstacle present.
PRELIMINARY CHECKS
For a good operation of the automatic system for sliding gates, the gate or
door shall meet the following features:
- the track and relevant wheels must feature correct sizes and must un-
dergo adequate maintenance (in order to avert excessive friction during
the sliding of the gate).
- during operation, the door shall not excessively oscillate.
- a mechanical stopper (according to regulations in force) shall limit the
opening and closing movements.
WARNING
Overall dimensions of the gear motor expressed in mm.
POSITIONING OF THE FOUNDATION PLATE
It is very important to keep to dimension X shown in Fig.2. This value de-
pends on the type of rack used:
X = 52 mm for rack in nylon
X = 49 mm for rack in iron, 12x30mm
Preset a corrugated tube (Fig.2 -A) for the passage of power supply cables
and connection wires for the accessories.
Check that, at the end of the fitting, the foundation plate is perfectly parallel
with respect to the wing.
Fit the system with screw anchors on the bottom of the cement (Fig.3).
Drill 4 holes, diam.10mm, by using the foundation plate as drilling template.
Tightly anchor the foundation plate to ground through the 4 "T" steel screw
anchors and the 4 "B" threaded bars, M8x150mm and corresponding "D"
nuts and "R" washers.
Alternative fitting systems are available on the market, e.g. anchoring with
retaining expansion band (Fig.3 -T2) to be inserted in the hole with some
hammer strokes.
INSTALLATION
FIG.1
FIG.2-3-4-5
9