Broan Powerpack Inserts PM400SSV Instrucciones De Instalación, Uso Y Cuidado página 6

For ADA compliance installation guidelines, please type the model number into our website.
RECOMMENDED TOOLS AND ACCESSORIES
• Measuring tape
• Phillips screwdriver no. 2
• Nut driver or socket 3/8"
• Flat blade screwdriver (to open knockout holes)
• Saw (to cut holes in cabinet)
• Sheet metal shears
• Pliers
• Metal foil duct tape
CONTENTS
Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the
manufacturer.
Make sure that the following items are included:
PM400SSV
(1) G F
REASE ILTER
C B
ABINET RACKETS
( )
ATTACHED TO THE BACK OF THE UNIT
(1) P B
ARTS
(4) N . 8-18 1/4"
O X
M S
ETAL CREWS
(8) N . 8-15 5/8"
O X
P H
AN EAD
W S
OOD CREWS
* F
IND PARTS BAG BEHIND THE WIRING COMPARTMENT COVER
INSTALL THE DUCTWORK
(DUCTED INSTALLATION ONLY)
NOTE: To reduce the risk of fire, use only metal ductwork.
1. Decide where the ductwork will run between the hood and
the outside. (FIG. 1)
2. A straight, short duct run will allow the unit to perform most
efficiently.
3. Long duct runs, elbows, and transitions will reduce the
performance of the unit. Use as few of them as possible.
Larger ducting may be required for best performance with
longer duct runs.
4. Install wall cap or roof cap (sold separately). Connect metal
ductwork to cap and work back towards the unit location.
Use 2" metal foil duct tape to seal the joints between
ductwork sections.
(1) 6" R
OUND
D A
AMPER SSEMBLY
(
ATTACHED TO ONE SIDE THE UNIT
(1) 3¼" 10"
X
D A
AMPER SSEMBLY
(
ATTACHED TO THE BACK OF THE UNIT
* C :
AG ONTAINING
(4) N . 8-32 1/4"
O X
M S
ACHINE CREWS
(4) N . 6-18 5/8"
O X
T H
RUSS EAD
W S
OOD CREWS
.
• Scissors (to cut metal foil duct tape)
• Pencil
• Wire stripper
• 2 Appropriate wire nuts
• Strain relief, 7/8" diameter (to secure house wiring
cable to the hood)
• Liner (optionnal)
PM600SSV
(1) H B F
YBRID AFFLE ILTER
)
(1) 8" R
OUND
)
D A
AMPER SSEMBLY
(
ATTACHED TO ONE SIDE THE UNIT
(1) P
(4) N . 8-18
O X
M S
ETAL CREWS
(8) N . 8-15
O
P H
AN
W S
OOD
* F
IND PARTS BAG BEHIND THE WIRING COMPARTMENT COVER
POWERPACK
24"
MIN
ABOVE COOKING SURFACE
C B
ABINET RACKETS
(
ATTACHED TO THE BACK OF THE UNIT
(1) 3¼"
(1) 6" R
D
OUND
AMPER
D A (
AMPER SSEMBLY ATTACHED TO
)
THE BACK OF THE UNIT
B * C :
ARTS AG ONTAINING
1/4"
(4) N . 8-32
O
M
ACHINE
5/8" (4) N . 6-18 5/8"
X O X
T H
EAD RUSS EAD
W S
CREWS OOD CREWS
.
R
8"
OOF CAP
ROUND DUCT
(PM600SSV
6"
ROUND DUCT
3¼" 10"
OR X
H
OUSE WIRING
INSERT
W
ALL CAP
3¼" 10"
X
- 30"
MAX
)
10"
X
A
SSEMBLY
)
1/4"
X
S
CREWS
),
ONLY
,
DUCT
DUCT 5
FIG. 1
10-0548