RIDGID R86006 Manual Del Operador página 8

OPERATION
NOTE: You might hear a whistling or ringing noise from the
switch during use. Do not be concerned; this is a normal
part of the switch function.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 3, page 12.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the drill
held in normal operating position, the direction of rotation
selector should be positioned to the left of the switch trigger
for forward drilling. The drilling direction is reversed when
the selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when not
in use.
CAUTION:
To prevent gear damage, always allow the chuck
to come to a complete stop before changing the
direction of rotation.
To stop the drill, release the switch trigger and allow the
chuck to come to a complete stop.
NOTE: The drill will not run unless the direction of rotation
selector is pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage may
cause the drill to become overheated. If this occurs, cool the
drill by running it without a load and at full speed.
KEYLESS CHUCK
See Figure 4, page 12.
The drill has a keyless chuck to tighten or release drill bits
in the chuck jaws. The arrows on the chuck indicate which
direction to rotate the chuck body in order to GRIP (tighten)
or OPEN (release) the drill bit.
WARNING:
Do not hold the chuck body with one hand and use
the power of the drill to tighten the chuck jaws on
the drill bit. The chuck body could slip in your hand,
or your hand could slip and come in contact with
the rotating drill bit. This could cause an accident
resulting in serious personal injury.
TWO-SPEED GEAR TRAIN
See Figure 5, page 12.
The drill has a two-speed gear train designed for drilling or
driving at LO (1) or HI (2) speeds. A slide switch is located on
top of the drill to select either LO (1) or HI (2) speed. When
using drill in the LO (1) speed range, speed will decrease
and unit will have more power and torque. When using drill in
the HI (2) speed range, speed will increase and unit will have
less power and torque. Use LO (1) speed for high power
and torque applications and HI (2) speed for fast drilling or
driving applications.
NOTE: If you have difficulty changing from one gear range to
the other, turn the chuck by hand until the gears engage.
CAUTION:
Never change gears while the tool is running.
Failure to obey this caution could result in serious
damage to the drill.
ADJUSTABLE TORQUE CLUTCH
This product is equipped with an adjustable torque clutch
for driving different types of screws into different materials.
The proper setting depends on the type of material and the
size of screw you are using.
ADJUSTING TORQUE
See Figure 6, page 13.
There are twenty-four torque indicator settings located on
the front of the drill.
 Rotate the adjusting ring to the desired setting.
• 1 - 4
• 5 - 8
• 9 - 12
• 13 - 16 For driving screws into hard wood
• 17 - 23 For driving large screws
•
LED LIGHT
See Figure 7, page 13.
The LED light under the chuck of the drill will come on
when the switch trigger is depressed. This provides
additional lighting on the surface of the workpiece for
operation in lower-light areas.
BIT STORAGE
See Figure 8, page 13.
When not in use, bit provided with the drill can be placed in
the storage area located on the base of the drill
INSTALLING BITS
See Figure 9, page 13.
 Lock the switch trigger by placing the direction of rotation
selector in the center position.
 Open or close the chuck jaws to a point where the opening
is slightly larger than the bit size you intend to use. Also,
raise the front of the drill slightly to keep the bit from falling
out of the chuck jaws.
 Insert the drill bit.
8 – English
For driving small screws
For driving screws into soft material
For driving screws into soft and hard
materials
For heavy drilling