Shark AI ULTRA ROBOT RV2600WSEU Manual De Instrucciones página 14

STEP 1 PREP THE ROBOT
..........
Side Brush
• Remove protective film from robot and dock.
• Attach side brush.
STEP 3
CHARGING YOUR ROBOT
6
h
First
Charge
INDICATOR
• Place robot on base to charge for 6 hours.
• When the robot is properly aligned with its BACK
against the base, the Charging Icon on the top
right side of the base will illuminate and the
Battery icon on the robot will illuminate.
• Make sure the robot is properly aligned on the base.
• TO TURN ON ROBOT: Place robot on base or press
and hold the CLEAN button for 5 to 7 seconds
until the indicator lights turn on.
CAN'T CONNECT TO WI-FI?
Restart your phone
• Turn off phone, wait a few minutes, then turn it back on
and connect to Wi-Fi.
Reboot your robot
• Take robot off dock and press and hold down the
CLEAN button on the robot for 12 seconds. Turn your
robot back on by placing it on the dock.
Reboot your router
• Unplug the router power cable for 30 seconds, then
plug it back in. Allow several minutes for your router to
reboot completely.
sha rkcl e a n.eu
SETUP
STEP 2 SET UP THE SELF-EMPTY BASE
1m
1m
1.5m
• Find a permanent location for the base in a central
area with a strong Wi-Fi signal.
• Remove any objects that are closer than 1m. from either
side of the base, or closer than 1.5m. from the front.
• Plug in the base. The Base Power Indicator Icon
on the top right side of the base will illuminate when
the basehas power. Make sure the power switch on
the back of the base is in the (I) ON position.
STEP 4 DOWNLOAD THE APP
SharkClean
App Features
UltraClean
✔
Scheduling
✔
No-Go Zones
✔
Mopping Modes
✔
Vacuum Modes
✔
Carpet Zones
✔
Search "SharkClean" in the app store or scan the QR
code on the front cover to download the app.
Questions? Steps if You're Stuck:
Having trouble connecting to your robot?
For how-to videos, FAQs, troubleshooting, and tips &
tricks visit: sharkclean.eu.
For full instruction booklet visit: qr.sharkclean.com/
qr.sharkclean.com/RV2600WSEU or
SCAN HERE USING YOUR SMARTPHONE CAMERA
• To use the app, your phone must be
connected to a 2.4 GHz network. The app
will not work on a 5 GHz network.
• DO NOT use a VPN or a proxy server.
• Make sure Wi-Fi isolation is turned off on the router.
Your robot will need to complete an Explore Run
without the mopping Module attached to create a
map of your home.
In the Explore Run, your robot will wander around
your home as it creates a map.
After this run, you can create Carpet Zones in the
areas of your home that you want to the robot to
avoid while mopping. If you do not want to set up
Carpet Zones, or do not have carpets or rugs in your
Place base home, you can skip this step.
on bare
Now you're ready to clean.
floor against
the wall.
Attach the fluid mopping Module to your robot to enter Mopping Mode.
ATTACH MOPPING PAD
• Insert the flat edge of the pad through the slot
in the mopping Module.
• Secure to the back of the mopping Module.
INSERT MOPPING MODULE INTO ROBOT
• Firmly push the
mopping Module
into the back of
the robot. (Do not
remove the dust
bin.)
• When properly
inserted, the
mopping Module
will click securely
into place.
• Your robot is
ready to
simultaneously
vacuum and mop
your hard floors.
BEFORE YOU CLEAN
INTERACTIVE MAP WITH CARPET ZONES
HOW TO SET UP MOPPING MODE
In this mode, your robot will vacuum and mop simultaneously.
• Fill with water to the water line.
REMOVE MOP ACCESSORIES AFTER USE
• Press the release button at the fill port and slide out
the mopping Module.
• Pour out the water.
• Remove the pad and
Remove the pad and
follow the care
instructions on the
back of the pad.
FILL MOPPING MODULE
s ha rkc lea n.eu