GE VTW525 Manual Del Propietario E Instrucciones De Instalación página 18

Troubleshooting Tips... Before you call for service
Problem
Lint or residue on
clothes
Clothes too wet
Blinking Spin light
or Spin light on at
end of cycle
Pilling
Snags, holes, tears,
rips or excessive
wear
Wrinkling
Back and forth
"swoosh"
"Clicking" behind
Control during fill
Water flow changes
during fill
Motor sounds during
spin
"Humming"
"Gurgling"
Washer rocking/
moving
Clicks, water flowing, gear sounds followed by pauses, and electric hum sounds are all part of
the normal wash cycle.
To listen and watch videos of normal washer operation, please go to
http://products.geappliances.com/appliance/gea-support-search-content?contentid=23061
or scan the QR code.
18
Possible Causes
Clothes are air or line
dried
Incorrect sorting
Detergent not dissolving
Overloading
Incorrect use of fabric
softener
Wash load out of balance
Out of balance
condition has been
detected
Result of normal wear
on poly-cotton blends
and fuzzy fabrics
Pins, snaps, hooks, sharp
buttons, belt buckles,
zippers and sharp objects
left in pockets
Undiluted chlorine
bleach
Incorrect wash and dry
cycles
Improper sorting
Overloading
Repeated washing in
water that is too hot
Electric motor reversing
direction
Automatic Temperature
Control Valve
Automatic Temperature
Control Valve
Motor ramping up/down
during spin cycle
Water drain pump
Drive motor
Water drain pump
Washer leveling legs
uneven
If you do not dry your clothes with a clothes dryer, your clothes
may retain more lint.
Separate lint producers from lint collectors.
Rewash and next time try a liquid detergent and/or use warmer
water temperature.
Loosely load clothes in the washer basket. For best results, load
items around the outside of the basket.
Check fabric softener package for instructions and follow
directions for using dispenser.
Make sure you have selected the EXTRA RINSE option.
Redistribute load in washer.
Allow cycle to continue and finish.
The unit will attempt to redistribute the load and reach full
spin. If unsuccessful, the app will notify the user that they must
return to the machine and redistribute their laundry. If this is not
completed within the time given, the session will cancel/time out
and the user must scan the QR code and start the cycle again.
While this is not caused by the washer, you can slow the pilling
process by washing garments inside out.
Fasten snaps, hooks, buttons and zippers.
Remove loose items like pins, objects in pockets and sharp
buttons.
Turn knits (which snag easily) inside out.
Check bleach package instructions for proper amount.
Never add undiluted bleach to wash or allow clothes to come in
contact with undiluted bleach.
Match Cycle selection to the type of fabric you are washing
(especially for easy care loads).
Avoid mixing heavy items (like jeans) with light items (like blouses).
Try a fabric softener.
Loosely load clothes in the washer basket.
Wash in warm or cold water.
This sound is the motor rotating back and forth to clean your
laundry.
Two valves mix cold and hot water. The "clicking" is when either
valve turns on or off to raise or lower the fill water temperature.
Two valves mix cold and hot water. The "clicking" is when either
valve turns on or off to raise or lower the fill water temperature.
The motor will speed up incrementally during the spin cycle.
When spin is complete, it will coast until it stops.
The drain pump will make a humming sound when pumping out
water after agitation stops and continue until spin is complete.
The drive motor will make a "humming" sound during the wash
and spin phases of the cycle.
When the pump starts drawing in air, It starts to gurgle. The washer
should then begin spinning and the sound will continue until it is
done spinning.
To level the washer, adjust the leveling legs by rotating the individual
leg in the proper direction for up or down.
What To Do
49-3000258 Rev 4